Please help me with a diagram for hs-23 plug connections...

Hey benblay7. Cutting the wire was not stupid at all.

Two of the wires are ground and are tied together and soldered to the ground terminal. These should be the same color, usually a shiny copper color. The ground is negative. The tip of the plug should be wired to the left side and the center is, of course, the right.

Check this out: explainthatstuff.com/howtorepairheadphones.html

Good luck from Detroit, MI.

If the wires are open or the connections are visibly broken then the connections can be mended. But if there is fault in the earpieces then I suggest that cost a new one must be checked before you think of getting this repaired.

You didn't specify of its a 61 or a 61 Rancher. Here's the info you need to take to your Husky dealer. The diagram will be with the major repair kit.
Model 61, then the 61 Rancher:
CARBURETOR Model 61: Tillotson HS-163A, B , HS-254A series or
Walbro WS series MAJOR REPAIR KIT: RK-23HS for HS-163A MINOR REPAIR KIT: DG-5HS/T for HS-163A

CARBURETOR Model 61 Rancher: Tillotson HS-163A series or
Walbro WS-17A, B series MAJOR REPAIR KIT: RK-23HS
K10-WS MINOR REPAIR KIT: DG-5HS/T
D10-WS

there are series of problem in xbox which can be solved without much technical knowledge your problem is one amoung that ........ your problem belong to that so dont worry i will give you the link to download the repair guide that will help you a lot Click Here

The Center High Mounted Stop Light work directly with the Brake Light system, so, review the Rear Lightning (Fuses 6, 23 and 27)

- WJ Repair Manual Section-08L-Lamps-Ewj8l (page 10, fig. 4)
- WJ Repair Manual Section-08w-Wiring-Diagrams-ewj8w

I hope help you. Good luck.

Error code 31:23 shows problem in Take-up Reel section of your Sony Camera. If you know about camera repair, please check Take-up Reel section in tape mechanism and if you don't know, please contact nearest Sony Service Center for proper repair.

Assuming that the joint which connects the neck strap has been damaged ( see below image )


, I advice you fix the loosed or broken joint back in its proper place permanently by using fevi kwik or some other fast bonding adhesive, but the only problem which will remain is that each time you have to use the headset you will have to wear it through your head andremove it the same way.

Rub the pins of your headset, and your phone with some tissue paper or something like that.
You might use some cleansining agent like alcohol.

Switch off your phone while doing that.



I too encounter such problems.

hey kev.. all i can ask you is ... the following 1) open the ear piece of the non working .. then take a multimeter (keep meter in resistance mode) and check the resitance if its good it will show you.. apx 32 0hm and if its showing you 0 or .1 or below 16 ohms.. 2) after you disconnect the speaker.. the broken one that is... chek the cable connectivity.. or rather continuity.. for this keep the meter in continuity mode the pervious resistance mode.. then take one wire and connect one prob from meter to it.. and take the other prob and connect ti too the pins of the cnnector.. ( here is there are 4 pins dedicated to the ear phone.. 2 for each.. nd they are towards the end sid.. just below the # key.. frm # key the last 4 pins connectors are for audio.. ) check the.. pins on the cord connector not the phone.. i hope you can find what wrong with your... head set now.. and yeah if the speaker is out jsut replace both the ear piece with sony or aiwa earphones.. it wil work best if your cable is gone then all the best buy a new one tc aditya

Buy other.