Re: Need to know on the 14 pin connector what color wire...
I would go to www.millerwelds.com and download the owners manual based on your serial number. It will insure you get the correct wiring diagram for your feeder.
- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
Based on the information provided, it seems that there may be an issue with the Remote 14 connection on the Miller Synco Wave 350 DX TIG/arc welder. Here are some steps that can be taken to troubleshoot the issue:
1. Check the Remote 14 connection: Make sure that the Remote 14 connector is securely plugged into the welder. If it is loose or not fully connected, this could cause issues with the pedal not being recognized.
2. Check the pedal connection: Ensure that the pedal is properly connected to the Remote 14 connector. If it is not plugged in all the way or if there is any damage to the cable, this could cause issues with the pedal not being recognized.
3. Check for error codes: The Miller Synco Wave 350 DX TIG/arc welder has a built-in diagnostic system that can display error codes if there is an issue with the machine. Check to see if any error codes are displayed and refer to the user manual for troubleshooting steps.
4. Contact Miller customer support: If none of these steps resolve the issue, it may be necessary to contact Miller customer support for further assistance.
In summary, if your Remote 14 is not reading your pedal on your Miller Synco Wave 350 DX TIG/arc welder, you should check the connections, look for error codes, and contact customer support if necessary.
I'd make 110% sure the internal parts are the same. It would surprise me if they were compatible. You will probably be better off using the right peddal.
Pin Number
Wire Color
Function
1 White Left Front Positive 2 Green Left Rear Positive 3 Violet Right Rear Positive 4 Grey Right Front Positive 5 Blue/White Amplifier Remote 6 Blue Antenna Remote 7 Red Accessory 12 Volts 8 Black Ground 9 White/Black Left Front Negative 10 Green/Black Left Rear Negative 11 Violet/Black Right Rear Negative 12 Grey/Black Right Front Negative 13 Sky Blue Telephone Mute 14 Orange/White Illumination 15 Not Used Not Used 16 Yellow Constant 12 Volts
This is the pinout shown on the Sony website for the CDX series players.
Pin numbering is as follows:
1 2 3 4 5 6 7 8
9 10 11 12 13 14 15 16
This is looking at the connector with the wires towards you.
Pin
Number Wire Color Description 1 White Left front + 2 Green Left
rear + 3 Purple Right rear + 4 Gray Right front + 5 Blue/white
AMP Remote 6 Blue ANT Remote 7 Red Accessory 8 Black Ground 9
White/black Left front - 10 Green/black Left rear - 11
Purple/black Right rear - 12 Bray/black Right front - 13 Sky blue ATT 14 15
Orange/white Illumination 16 Yellow Battery
This is the pinout shown on the Sony website for the CDX series players.
Pin numbering is as follows:
1 2 3 4 5 6 7 8
9 10 11 12 13 14 15 16
This is looking at the connector with the wires towards you.
Pin Number Wire Color Description 1 White Left front + 2 Green Left rear + 3 Purple Right rear + 4 Gray Right front + 5 Blue/white AMP Remote 6 Blue ANT Remote 7 Red Accessory 8 Black Ground 9 White/black Left front - 10 Green/black Left rear - 11 Purple/black Right rear - 12 Bray/black Right front - 13 Sky blue ATT 14 15 Orange/white Illumination 16 Yellow Battery
×