Error code 1201

Error Code: C1201.
Description: Engine Control System Malfunction.
Trouble area:
- Inspect engine control system.
- Wiring.
- ECM.
Error Code C1422.
Description: Master Cylinder Pressure Sensor Zero Point High Malfunction.
Trouble area:
- Stop light switch Stop light switch circuit
- Master cylinder pressure sensor circuit
- Brake actuator assembly (Master cylinder pressure
sensor).

have you read your book that came with your refrigerator if you don't have one go online with your make and model number and look up Samsung refrigerator then after you fine it print it up

Hi.

Go to HP support page for this printer, download the manual and refer to the manual to fix the problem. If that is not enough, refer to HP online troubleshooting or ask a new question to Fixya,

Here the printer support page: HP Photosmart C5280 All-in-One Printer - HP technical support

All the best.

G.

The error message describes that: "The print carrier stopped before all of the data was used."

To reset the error code , try the following steps:

1. Power the printer off.
2. Remove all cables from the back of the printer.
3. Reinsert the power cord.
4. Switch the printer back on.
5. Check the operator panel to see if the 1201 error message is displayed.
6. If the error message returns, the printer could be defective.
   
7. Contact Lexmark Customer Support for further troubleshooting and warranty options.

Problem Error 1201; Carrier stall; Printer stopped Solution The definition corresponding to this error message is this: "The print carrier stopped before all of the data was used." To resolve this issue, please do the following:

1. Power the printer off.
   
2. Remove all cables from the back of the printer.
   
3. Reinsert the power cord.
   
4. Switch the printer back on.
   
5. Check the operator panel to see if the 1201 error message is displayed.
   
6. If the error message returns, the printer could be defective. Contact Lexmark Customer Support for further troubleshooting and warranty options.

I’m happy to help further over the phone at https://www.6ya.com/expert/jonathan_828b54f422cbefdd

error code 3501 means the front access door is open on the printer. Error code 3502 means the paper tray is empty. The error code 3602 means the print job did not finish printing.

for more hrlp visit CBR Tech Solutions

Kindly try this:

- Power the printer off.
- Remove all cables from the back of the printer.
- Reinsert the power cord.
- Switch the printer back on.
- Check the operator panel to see if the 1201 error message is displayed.If the error message returns, the printer could be defective. Contact Lexmark Customer Support for further troubleshooting and warranty options.

Hello, erorr 1203 is telling you there is one of a few issues with your cartridge/s. Check the contacts are cleaned and printheads. Make sure there are no paper jams. Reset the printer by turning it off and completely unplugging it and replugging it and turn it back on again. Clear print queue, check it is set to work offline in settings. Press copy and copy something and see if it is ok now. Error 1201 is a communication issue with data where your cartridge has stoped for one or more reasons and h eprint data was not completed or used. Try the reset to fix this too. Post back if no good. Don't forget to clear print queue.

The definition corresponding to this error message is this: "The print carrier stopped before all of the data was used."

To resolve this issue, please do the following:

1. Power the printer off.
2. Remove all cables from the back of the printer.
3. Reinsert the power cord.
4. Switch the printer back on.
5. Check the operator panel to see if the 1201 error message is displayed.
6. If the error message returns, the printer could be defective. Contact Lexmark Customer Support for further troubleshooting and warranty options.

Thank you

The definition corresponding to this error message is this: "The print carrier stopped before all of the data was used." To resolve this issue, please do the following:

1. Power the printer off.
2. Remove all cables from the back of the printer.
3. Reinsert the power cord.
4. Switch the printer back on.
5. Check the operator panel to see if the 1201 error message is displayed.
6. If the error message returns, the printer could be defective. Contact the printer company if within warranty they will replace the printer.