Strimmer not working so used a new carb rebuild kit, strimmer started 2nd pull, carb only has a low speed screw and a idle screw attached to the throttle cable. Accelerates no problems, but idles to high. Idle screw adjusted as far as possible, low speed screw turned out 1 turn from seat. By the way it's about 15 years old, could it possibly be a clutch problem and weights worn and not returning to there neutral position when speed is reduced..
SOURCE: have 1987 nissan sentra wagon 1.6 carb.engine the
Check your Ignition timing before anything
check your plugs see what color they are
red or orange means carb is to lean , black
or oil means to rich then you can go from there
and set mixture screws on carb , let me no how you make out .
SOURCE: will not run
Remove the water trap bowl at the bottom of the petcock, (gas valve). Any water or trash in the bowl? Drain a cup of gas from the tank. Any water or trash in the cup? Dump it, clean it and re-mount it, ( not all bikes have a water trap bowl ).
Drain the carburetor. There may be a screw on the lower side of the carb float bowl. Remove the screw then replace it after the fuel drains. Turn the gas back on and wait a minute for the carb to fill with gas. Install a new stock NGK spark plug and try to start the engine. If the bike doesn't start and run properly then shut off the gas and remove the carburetor from the engine.
Remove the float bowl and clean the entire carb with a spray carb cleaner from the auto parts store. Wear protective goggles to avoid getting spray in your eyes. Spray into all the little airways and fittings in the carb. Remove the two screws on the outside throat of the carb and spray into the screw holes as well.
< < READ CLOSELY > >
Be sure to put these two screws back in the same hole they came out of. IMPORTANT > do not tighten these two screws down. Only screw these in until they LIGHTLY seat. Now turn each screw one and one half turns outward. Put the rest of the carb back together, clean the air filter and install the carb. Be sure the bolts are tight. Let the float bowl fill then start the engine. Set the idle speed with the idle screw, (sticks out from side of carb perpendicular to the carb throat).
If you are smoking that badly, loose the gas in the tank and start fresh with a 32/1 gas/oil mix. That equals 4 ounces of TWO STROKE OIL to one gallon of gas. Do NOT use motor oil in the gas. It may continue to smoke for awhile, until it rids it'self of built up oil in the crankcase.
On the clutch, be sure the oil level in the gearbox is correct. This is where 10w40 motor oil goes. Check the clutch cable linkages. One at the clutch lever and possibly one at the motor. You should have about 1/4" play in the clutch handle before the lever starts actually pulling the clutch.
You can download a free PDF service manual from this site > >
http://www.carlsalter.com/motorcycle-manuals.asp I checked and your manual is on the list.
Please rate this solution. Thanks!
SOURCE: mcculloch strimmer/brush cutter - cuts out when throttle opened
Hi sounds like it could need a diaphram kit in the carby if it has mixture screws one markedl for low speed and one marked h for high speed you can try winding out the low speed screw a bit but if that does not work it will definatly need a kit.
SOURCE: 25 yr old Husqvarna 266. starts fine, lots power, but won't idle.
I think you have exceded our level of help. Please try here.
ArboristSite.com Chainsaw thread (free to join)
http://www.arboristsite.com/forumdisplay.php?f=9
You might read this thread
http://www.arboristsite.com/showthread.php?t=110858&highlight=husky+266
I searched for "Husky 266" and got many positive hits. She is a respected machine.
http://www.acresinternet.com/cscc.nsf/ed1d619968136da688256af40002b8f7/9f5525102886abf488256b52001a33af?OpenDocument
HTH
Lou
SOURCE: Poulan Pro PPB250E trimmer won't idle
clean and repair carb, make sure the mounting gasket is ok. and does not have a vacuum leak.
492 views
Usually answered in minutes!
×