How to instale frequency back in - Radio Communications

neighbor operating a remote control and it being picked up by the control box
talk with the manufacturer /installer of the controller to get a "roving frequency remote" to stop what is accurring
It also stops thieves from reading your frequency on their scanners to gain access to your garage
the installer will be able to explain how it works

Your replacement radio is defective. Full stop.

Info from the manual:

Memory configurations

You can install 128 MB, 256 MB, 512 MB, and 1GB DDR SDRAM DIMMs into the DIMM sockets using the memory configurations in this section.

• Install only identical (the same type and size) DDR DIMM pairs

using the recommended configurations.

• Make sure that the memory frequency matches the CPU FSB

(Front Side Bus). Refer to the Memory frequency/CPU FSB

synchronization table on the next page.

• This motherboard does not support double-sided 16-bit DDR DIMMs.

• Do not create a three-DIMM configuration in dual-channel mode. The
third DIMM is ignored in the dual-channel operation.

Recommended memory configurations

Memory frequency/CPU FSB synchronization

* Use only identical DDR DIMM pairs.

Sockets

Mode DIMM1 DIMM2 DIMM3 DIMM4

Single-channel (1) Installed - - -

(2) - Installed - -

(3) - - Installed -

(4) - - - Installed

Dual-channel* (1) Installed - Installed -

(2) - Installed - Installed

(3) Installed Installed Installed Installed

CPU FSB DDR DIMM Type Memory Frequency

800 MHz PC3200 400 MHz
533 MHz PC3200/PC2700 400/333 MHz

That is not your problem. VOIP has issues switch back to a regular phone line. You can not change the frequency of your phone with out buying a new one that uses a different frequency you can change the channel but none of these options will fix your problem.

The Asus P4S8X-X has C.P.R.

CPU Parameter Recall

(Central Processing Unit, or Processor)

Restart the computer, and BIOS will set the CPU parameters back to the factory default settings.

Internal frequency rate times the multiplier = external frequency rate.

The Asus P4S8X-X uses Intel processors (Socket 478) that have either a 400Megahertz Front Side Bus, or a 533MHz FSB.

Since you did not state what socket 478 Intel processor you have installed, I cannot tell you what the external frequency rate is supposed to be.
(At maximum operating capacity)

Have you installed a different Processor?
Were you trying to overclock?
What led up to this?

Hi, Please try the below mentioned steps: AUTO SORT OFF B4 U MANUAL SCAN A CHANNEL/S: Go into Menu / Installation / Fast Install and press OK (enter pin) Now press the red button on the remote for advanced install Scroll down the options and turn Fav Sort off then press exit (do not press OK) if you press OK all channel order will get sorted back to the default order MANUAL SCAN ALL CHANNEL?S: follow AUTO SORT OFF After you press exit you get a list of frequency?s press red button (update) to update all channels MANUAL SCAN ONE CHANNEL: On the channel that?s scramble press the info button twice and make a note of the frequency at the top left, now follow AUTO SORT OFF when u press exit u get a list of frequency?s scroll down till you get to the frequency you made a note of and press ok to tick the box then press blue button for manual scan else....do a factory reset on the box m8 then rescan for chanells then leave your box on sly sports 1 to update

All factory installed frequencies are between 462.000 - 468.000 MHz. They consist of FRS frequencies and some GMRS frequencies.

Here is a link to the User Guide (which does not seem to have a frequency chart) http://www.giantintl.com/ContentManage/manuals/Moto/T5320_T5410_T5420_User_Manual_E.pdf

Best regards.

It sounds like the frequency referred to is the monitor's frequency. If it's an LCD monitor, the frequency is usually 60Hz. If you are using a VGA cable, it's guessing the frequency and has guessed wrong.
The other possibility is that the Railroad Tycoon game sets the screen resolution and frequency to something your monitor is not capable of displaying. It sees a nice graphics card and shoots the settings to the top of the range. If you can change the settings before playing the game, you might get it to work.

try this it should help.

Try and determine the lowest transponder frequency that you can get a signal on.
Look at the frequencies you already have on the channels saved so far and choose the lowest.
Then in the installation menu select MANUAL SCAN and set that as the frequency.
Make sure you can see a signal and scroll down to Network scan and change to ENABLE with the Right arrow.
While still highlighted, click OK.
Scanning should then begin. It will say 1/1 to start with but should then jump up to 1/?? (the ?? being 2 digits).

simply your scanner range is from 77 to 90 mhz. you can not listen to any higher frequencies than that.