I have no caller I'd from bell. Can I have name or number displayed from numbers on my directory. If so how do I do it. Thanks

Do name/number display on any other phones on that line?

If that is your only phone, try borrowing another with working call display from a friend or neighbor. If another phone doesn't display caller info, call your phone company - most charge extra to provide caller number ( and in some cases, another extra to add the name). Even if the features are included in your rate, it's possible they weren't turned on correctly.

Your Panasonic may also have a setting to show name or number - depending on the display size, you may have to pick one or the other.

Finally, some phones do not support exactly the same caller ID info that the phone company sends - I have seen some which displayed number instead of names and no name, just because the two pieces of equipment did not agree on the standard. Try your Panasonic on someone else's line with working Caller ID.

ity is possible that the caller has blocked his number from being displayed
if other caller numbers are being displayed but not that one , that will be the case
if not reset the settings for caller id

No........

CS6319-4 Features:

• New DECT 6.0 Technology
  - Interference Free Communication
  - Increased Clarity / Enhanced Security
  - Wider Range / Network Friendly
• 1.9GHz Cordless Phone
  - Dedicated for Cordless Phones by the FCC
  - 30% Battery Life Increase Over 5.8GHz
• Caller ID / Call Waiting
• Expandable Up To 5 Handsets
• Wall Mountable
• Handset Speakerphone
• Backlit LCD Display
• Backlit Keypad
• Name / Number Caller ID Memory
• 100 Station Phone Directory / Dialer
• Conferencing
• Selectable Ringtones
• Handset Volume Control
• Handset to Handset Intercom
• Call Transfer
• Last Number Redial

Sounds like you shut the CCR tree down. Go to AA>table>1>CCR>chng>1>enable. that should take care of it

Hi

Thanks for using FixYa. I think you have stored more than 100 Caller ID messages and hence the caller ID is not showing on Uniden Tru8888. In the following cases the caller ID will not be shown-

If you answer a call before the Caller ID message is received (for example, before the second ring), the Caller ID message will not appear.

When the call is received via a telephone company that does not offer Caller ID service, the caller’s phone number and name does not appear. (This includes some international calls.)

When the call is via a private branch exchange (PBX), the caller's phone number and name may not appear.

You may receive any one of the following messages:

When a private name is received; Private Name
When a private number is received; Private Number
When a unknown name is received; Unknown Name
When a unknown number is received; Unknown Number
When invalid data is received; Incomplete Data

The Caller ID list stores information for incoming calls - even unanswered calls. You can store up to 100 Caller ID messages and phonebook entries (including Speed Dials) for each handset and the base. You can view the Caller ID list through the handset or base during a call or when the phone is in standby mode.

Memory locations for Caller ID messages and Phonebook entries (including Speed Dials) are common, you can store up to all 100 entries for each handset and the base. Caller ID messages are not stored when you have 100 phonebook entries. When you have stored a total of 100 phonebook entries and Caller ID messages, the oldest Caller ID message is overwritten.

Please do rate the solution and revert for further assistance.


Thanks
Rylee

Your system needs to have a mif-m card and kmm chip installed and all programming setup in order to scroll through the caller id. If this is all setup you can hit the directory button and than use the arrow buttons under the display to scroll. ldtsnj.com

First you need to verify if the caller id does that to all incoming calls, showing numbers only, or if it only does that to only numbers stored in directory. If it does that to all incoming calls then you need to check manual to see if there a setting to allow both name and number of all incoming calls. Either way you need to make sure caller id functions allows both name /number on display.

The KX-T7731 is a proprietary system phone. You have a Panasonic phone system. Caller ID is transmitted between the first and second ring but the phone system itself is the only part that gets this information. The system has to be compatible for caller ID and it has to collect the caller ID data and send this information to your phone(s). Your phone can be used on many different Panasonic phone systems. The phone's part number does not help you. First thing you need to do is find out what system you have and if it has caller ID. The phone system part number should start with KXT like your phone.

just go to your phone book option and erase that number which is dobble entry in book 2nd step is copy all numbers in phone directory if u r handset is multimedia u have to copy in phone mem or go to nearest mobile shop