How to pair a replacement Samsung remote AH59-02758A to Samsung soundbar

Here are steps to connect a Samsung soundbar to a Sanyo FVM3982 TV using an optical cable:

1. Locate the Optical Out port on the back of the Sanyo TV. This port will be labeled "Optical Out" and is usually covered by a small protective cap.
2. Remove the protective cap from the Optical Out port and plug in one end of the optical cable.
3. Connect the other end of the optical cable to the Optical In port on the Samsung soundbar. This port may be labeled "Optical In" or "Toslink".
4. Turn on both the TV and the soundbar.
5. On the Sanyo TV, use the remote to navigate to the audio settings. Look for an option to set the audio output to "External Speakers", "External Audio", or "Optical Out". Select this option.
6. Adjust the volume on the Samsung soundbar using its remote control.

Once these steps are completed, the sound from the TV should be played through the Samsung soundbar. If you encounter any issues or don't hear any sound, check to make sure that the soundbar is set to the correct input and that the volume is turned up. Additionally, make sure that both the TV and soundbar are properly connected and powered on.

Question edited for clarity.

No one buys Universal Remotes these days, they are so 1980! You buy a Facsimile Remote, an exact copy of the original like this one.

https://www.remotes.net/products/replacement-remote-for-nad-c720bee

https://www.google.com/search?q=remote+for+NADC720BEE

..

Connect the power cords for the soundbar and the subwoofer to the back of each, and then plug both into a wall outlet. Use a small pointed object to press the ID SET button on the back of the subwoofer. Continue holding until STANDBY turns off and LINK (Blue LED) blinks quickly.

You have a soundbar?
And the soundbar is paired?
Next... go to your TV remote control ... navigate into settings... and change the sound setting to external device

If you need further help, I’m available over the phone at https://www.6ya.com/expert/gene_9f0ef4df2f9897e7

Should be able to use Bluetooth. Need to "pair" the devices (the TV and the soundbar). On soundbar, press On/Standby to power it on, press Input to select Bluetooth (pairing indicator blinks), press & hold pairing button until pairing indicator blinks quickly. Now go to the TV's setup menus: Sound > Speaker Settings > TV Speaker > SoundShare Settings, Add New Device=On, select the Sharp GT-SB30 from device list. If passcode, password, etc is needed, enter 4 zeros (0000). After the devices are paired. the pairing indicator on the soundbar should stop blinking. The pairing information should be retained so you only have to do this one time unless you do a full reset on the TV or soundbar.

I presume you need link the Wireless Subwoofer to tour Soundbar.
Here are instructions:
How To Link The Wireless Subwoofer To Your Soundbar HW Models Samsung

turn the soundbar off, then press and hold the reset button on the back of the subwoofer until the blue light starts blinking fast. the point the remote at the soundbar and hold the mute button until"ID SET" shows on the display. Then turn on the soundbar and it should find the sub and pair with it.

Press and hold the reset button on the back of the subwoofer until the light on the front starts blinking. Then with the soundbar turned on, press the stop button on the soundbar and the mute button on the remote at the same time. The display should say "REMATE". The sub light should stop blinking then and should be linked.

My Samsung AirTrack soundbar was showing my iPhone 5 and my iPhone 5 was showing the soundbar was available. However, when I tried to connect them I got an error saying the connection was unsuccessful. So what I did was "forget device" and then paired them again. It worked right away. I hope this works!

Hi thanks, I got the Samsung customer support desk to assit me and fix the problem.. sorry for the bother -- I thought you were a samsung support site.