Question about Electrical Supplies

Open Question

Just replaced globe and it blew straight away

Posted by on

  • deton8 von Splosion Feb 25, 2019

    Hello Sue Breznikar,

    Seriously want HELP?

    Pretend that we don't READ MINDS...

    Give a TYPE of "GLOBE" so we can better guess what in the WORLD you might need help … with.

    Pretty please..

    EDIT your existing QUESTION

    Add a few relevant details...
    (as though you seriously wanted help).

×

Ad

2 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Anonymous

  • 1118 Answers

SOURCE: wipers stopped working

Sounds like wiper motor tied up. unhook electrical plug to motor and turn on wiper switch and see if it blows the fuse, if it dosent than its most likely wiper motor thats bad, if it blows fuse with it unhooked than it could be the switch.

Posted on Mar 04, 2009

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Am2 fuse blown,no dash lights a pair when i turn ignition key except engine oil light.when i replaced am2 fuse it blew straight away after briefly flashing up the engine light.


Aug 29, 2015 | Cars & Trucks

1 Answer

Side by side ice and water dispenser


Did you replace the bulb with one of the same voltage rating?

 

Seems strange that a new bulb should blow straight away, maybe it was faulty.

 

This sounds like a blown fuse.

 

Oct 13, 2007 | Frigidaire FSC23F7D Side by Side...

1 Answer

Low beam headlight not working


check globe - Could be element blown on low beam part of globe. A lot of globes are haligon globes with two elements my low beam filament blew two weeks ago and I just replaced the globe but if you look at the globe you will see one of the two filaments is vapourised (missing) if blown.

Aug 13, 2014 | Cars & Trucks

1 Answer

Replaced horn fuse and it blew again right away this is a pontiac transport 1997 help


The fuse blows to prevent wire melting and eventual fire! If it blows straight away then there will be a short circuit somewhere in the circuit, which means the electricity is going from the battery positive to the fuse then straight back to the battery negative without any resistance. You would have to follow the wiring and test components until the fuse no longer blows. :)

Jul 01, 2012 | 1997 Pontiac Bonneville

1 Answer

Westinghouse range hood wrf900cs light blew, light globes replaced but lights still not working


I had the same problem. An audible pop and the lights stopped. Fans still works, light bulb filaments appear intact.
My problem was that a short piece of the copper on the printed circuit board, inside the switch housing, had vaporized as if it were a fuse. I soldered a bridge of copper wire across the small 5mm gap and all was working again.
Access the switch compartment by removing the filters, undo a couple of retaining screws to remove switch unit.
Make sure the electricity to the unit is Off/unplugged before proceeding!!!
Switch unit cover has 4 screws holding it on. Once inside the unit, trace the wire (mine was grey colour) from the light switch to the small printed circuit board. The copper printed circuit link to the connector had gone...no sign of burning, just gooone!
Solder a bridge of copper wire across the gap and reassemble switch unit to test.
....send beer donations to me in qld...cheers!!!

Jun 29, 2012 | Kitchen Ranges

1 Answer

Wine cooler not working - checked all fuses and found the fuse on the circuit board had blown.Changed that fuse- reconnected and the fuse blew straight away what do I do next?


If the fuse blew immediately..then there is a hard short somewhere in the circuit...if you have an ohmmeter you will need to check the compressor, fan , and whatever type of controller for a short circuit

May 09, 2011 | Refrigerators

2 Answers

How to change globe on headlight ford focus 2005


avatar3.jpg

brian_au no 1 solution is wrong.. globe is under a spring clip cover . remove cover, then unplug, then release retaining spring behind the globe. replacement is just process reversal

Sep 18, 2009 | 2005 Ford Focus

1 Answer

How do I change my headlight bulb


go to your parts suppler and ask for a H4 globe pop your bonnet and remove the plug on the back of your head light then remove the rubber boot paying attention to which way it cam off then you will find a spring clip unclip it but be careful not to damage its anchor point. remove old globe an throw away take new globe out of box DO NOT TOTCH THE GLASS OF THE GLOB AS IT WILL CAUSE THE GLOBE TO BLOW STAAIGHT AWAY AFTER FITTING IT handle the globe by the metle bass and fit it, refit spring clip and rubber boot fit the plugf and check the operation of the light

bingo you are done have a nice day

Dec 21, 2008 | 1999 Mitsubishi Mirage

1 Answer

Electrical fault


Might have issues with ignitor, or solenoid for gas

Oct 28, 2007 | Belling DB2 Dual Fuel (Electric and Gas)...

Not finding what you are looking for?
Electrical Supplies Logo

Related Topics:

87 people viewed this question

Ask a Question

Usually answered in minutes!

Top Electrical Supplies Experts

Gene Haynes

Level 3 Expert

5391 Answers

Brad Brown

Level 3 Expert

18157 Answers

john h

Level 3 Expert

22486 Answers

Are you an Electrical Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...