How do I connect the white bottle to the homelite 80 bar power washer ?

Find an oil you like and mix it according to the oil recommendations.
I use Opti-2 in all my 2cycle fuel mix and it's a 100:1.
What the oil manufacturer says to mix the oil/fuel is what you go by, not what the engine manufacturer says.




Opti 2 2 Cycle Oil 34oz EZ Measure Bottle 20112 eBay

I'd love to help but need more info. What is the model # and can you describe the problem you having in more detail.

check the line fuse

Yes! Normally 32:1 gas oil mixture is what you will need. The easiest way is to buy the oil in pre-measured bottles (Usually available in 6 packs). That way all you have to do is add one bottle per one gallon of gas.
Hope this helps.
(Don't forget bar oil)

No 80 weight is to thick.

Yes you can do it yourself

Degas Bottle Removal

1. Drain radiator (8005) until engine coolant is out of degas bottle. Disconnect radiator overflow hose (8075) and engine coolant vent hose at degas bottle.
   

1. Remove power steering oil reservoir retaining screws and position power steering oil reservoir (3A697) out of the way.
   

1. Remove degas bottle return hose and clamp. Remove degas bottle retainers and remove degas bottle.
   

Installation

1. Position degas bottle in vehicle and install retaining screw and nut. Tighten retaining bolt and nut to 9-12 Nm (80-106 lb-in).
   

1. Connect degas bottle hose and clamp to degas bottle.
   

1. Position power steering oil reservoir onto degas bottle and install retaining screws securely.
   

1. Connect radiator overflow hose and engine coolant vent hose to degas bottle.
   

1. Fill and bleed engine cooling system as described. Check for coolant leaks and proper engine coolant level after engine reaches normal operating temperature.
   
   
   
   
   
   Item Part Number Description 1 8100 Radiator Cap 2 - Nut (1 Req'd) 3 - Bolt and Retainer (1 Req'd) 4 - Nut (1 Req'd) 5 - Bolt (1 Req'd) 6 - Coolant Recovery Hose 7 - Coolant Return Hose 8 - Coolant Recovery Hose 9 8A808 Degas Bottle A - Tighten to 9-12 Nm (80-106 Lb-In)

Hope this helps.

Zeppelinx12

3 oz. 2 cycle oil to 1 gallon fresh fuel and
to keep your fuel fresh add some fuel stabilizer found at walmart for ethanol blended fuel ( it will say marine formula on bottle) and add it to the gas can you fill your trimmer with ,follow directions on bottle for treatment vs. capacity.

If you are asking about chain lubrication we use "Bar and Chain" oil (SAE30 with additives to make it adhere).
If your question is the fuel/oil ratio, it is 50:1 - 4 liters of premium fuel to 80 milliliters of quality 2-cycle oil.
If the saw is not oiling the bar and chain please reply below with model number (UT-something) below. Vso srečo.

If you have more questions or need additional help please reply below and I will get back to you. Thank you for using FixYa and Good Luck. HTH
Lou

Coolant in 50% concentration goes into the coolant overflow bottle. Windshield wiper fluid into the wiper fluid bottle. Power steering fluid into the power steering fluid bottle.
You do not need to add any other fluids to these. Do not add water to the washer fluid bottle for example, if you drive in a climate that would allow it to freeze.

You might try psep.biz for the bar. They list some replacement bars that should fit the model number 240 that you listed. If you don't find what you need let me know and I will try another site.