Hobart legacy hl661 error code 1 - Hobart Dishwashers

Question edited to a lot more clarity.
Question translated to English. We are a North American site.
https://translate.google.ca/


No model given, 'Legacy' is a range of mixers.

'Er1' is a memory error. Page 3 refers.

https://manualzz.com/doc/4212431/hobart-hl200-error-codes-and-trouble-shooting

https://www.google.com/search?q=Hobart+legacy+ER1

..

Error P3, Rinse Tank Booster Thermister is faulty

SOLVED: Hobart LXI Dishwasher a P3 code is flashing ...

https://www.fixya.com > support > t4318217-hobart_lx...

Mar. 11, 2010 - It is monitoring the rinse temp. P2 is the booser probe, and P1 is the wash tank. The control board will store error codes, so once changed, you ... 1 answer · 11 votes: The p3error is an open or shorted booster thermistor.take off btm panel on the right side is the bstr, do when cold and no power to mach.,TURN OFF BREAKER, ...
SOLVED: What is p3 code on hobart am15 dishwasher - Fixya
Sep. 2, 2019
SOLVED: What does a P3 code mean? On a Hobart LXI high ...
Jan. 5, 2014
My hobart am15 display a p3 error code and i make - Fixya
May 1, 2010
SOLVED: Error code "p3" appears in the digital panel with a ...
May 12, 2010
More results from www.fixya.com

18H doesn't exist

https://www.google.com/search?q=hobart+lx18c+18H+error+code

..

HL662 is a Legacy Mixer
18 = Phase B over current fault (check fuse, contactor, short to ground, drive malfunction)

http://hobartfood.com.au/manuals/FOOD%20PREP/MIXERS/CURRENT%202011%20MIXERS/HOBART%20HL600/HOBART%20HL600%20MIXER%20TECHNICAL%20AND%20SERVICE%20INFORMATION/HOBART%20HL600%20SERVICE%20MANUAL/HOBART%20HL600%20ERROR%20CODES.pdf

It's meant to tell the operator that the bowl is not in proper operating position. If the bowl is in the proper position then the bowl in switch may be bad.

I replaced the probe temp according to error code P1 but the display still shows error P1. Is there any suggestion for further troubleshooting?

Check www.hobartservice.com for your local Hobart office.

Hobart mixer, HL300, stops and flashes as oc3, wounded what is broken?

error 99 stands for communication fault between timer board and the sr drive.there are 5 things that can cause this error.1.rs-485 cable disconnected or malfunction 2.1 con monitordisconnected or malfunction. 3.run/stop wiring disconnected or malfunction. 4.timer board malfunction. 5.sr drive malfunction. hope this helps, dont forget to vote, thanks, monomoy

i will try to help, always include ml# with problem description on any hobart pc. of equip. which is located on the info. plate. there are 2 v.f.d.for this mixer ,sr drive being 1st generation, and gen. elec drive 2nd generation, on the sr drive err23 indicates a motor stall condition there are 6 most likely causes for this err. 1st, batch size too large,ck. capacity chart. 2nd,encoder malfunction. 3rd,motor malfunction. 4th,drive malfuction. 5th,1 con coil malfunction. 6th,2 cr malfunction. if this does not help, repost problem and i will ck. to see if i can be of anymore help, please dont forget to vote for me thanks, monomoy

I know what these codes are: code 19 is that phase c is over current fault and code 23 is a motor stall fault.I would start by making sure you 3 phase wiring going into the mixer is there.I service these mixers as im a service tech for hobart.these units are very detailed and i can walk you thru some things to check but if you have an electrical problem you most likley will have to call a hobart service tech because we have special equipment to diagnose the fault.let me know it may be something simple as these mixers are usally maintenance free.