Question about Technics Audio Players & Recorders

Open Question

Technics sh 8055, spectrum display always showing max reading, even with everything disconnected,

Technics sh 8055, spectrum display always showing max reading, it was working before but has been taken out of storage. It is connected correctly and still shows max reading, disconnected everything and still shows max reading, must be electrical fault but not sure where.

Posted by on

Ad

6 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Anonymous

  • 4 Answers

SOURCE: technics ho2 no play error

u need a new motor in yr dvd player i had same problem so had new motor fitted cost 50 pound works now

Posted on Nov 13, 2007

Ad

Dave Hart

  • 189 Answers

SOURCE: connection between CD, EQ, SP technics

Each unit (the EQ and the Processor) should have left/right in/out rca jacks as well as L/R tape in/outs. The EQ or processor use the receiver's tape loop and then provide a tape loop to replace the one they've used on the receiver.

You plug the first unit (let's say the Sound Processor into your receiver/amp as if it were a tape deck (Processor's outs connect to reciever's tape ins (play) while the Processor's ins connect to the receiver's tape outs (record).

Then you chain the EQ off the Processor in the same way (EQ outs connect to Processor's tape ins (play) and EQ ins connect to the Processor's tape outs (record).

Last you connect the tape deck to the EQ as follows. Tape deck outs connect to EQ's tape ins (play) and the tape deck ins connect to the EQ's outs (record).

This will put both the Sound Processor and the EQ in the receiver's tape loop. In order to have all the receiver's source signals routed through them you may have to engage a Tape Monitor switch or button somwhere on your amp which will route the tape loop to your speakers.

Posted on Jan 09, 2008

Anonymous

  • 232 Answers

SOURCE: Technics SH-8017 Equalizer

use youe tape out signal into the eq's main input and the eq'sout back into the record side of ur tape source.

Posted on Aug 09, 2008

Anonymous

  • 1 Answer

SOURCE: technics sh-eh790 stereo system

Hi there just wondering, if you cant fix your problem would you sell your sound processor as mines broke beyond repair. My email is cocksure001@homail.co.uk.

Posted on Jan 14, 2009

rommelalilin

Rommel Alilin

  • 2178 Answers

SOURCE: I have technics reciever sa ax 6 (without tape

Click here.

Posted on Nov 23, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Technics SH-GE90 DSP gives off high pitch sound, no display in the window,only the red dots down the side and the demo button dose not change demo modes.


Check power supply capacitors.
These are prone to leakage on the SH-GE90 and can cause various
symptoms such as no display or in some cases a flickering display.

Dec 12, 2012 | Technics SH-GE90 Home Equalizer

1 Answer

Hello i need help please..... I have a Technics SU-Z550 and SH-8055 Graphic Equalizer My amp has lost power... lots.! its working one channel louder than the other but the one which is louder still has...


If the same channel is dead on the EQ as is dead on the amp there may be a correlation.

Let's break this into its two parts.

1) SU-Z550: You don't say WHAT source(s) you tried to use on the CD/AUX, TUner and PHONO inputs. The external device itself could be the source of the low volume. Try swapping the Left and Right cables to see if it follows the source channel or stays with the amplifier channel.

Check the controls on the amp to make sure you understand each one's effect on the sound.

"PHONO" is literal and exclusively FOR A TURNTABLE - NOTHING ELSE - EVER.

2) SH-8055: Equalizers don't 'boost' sound, they modify its levels at various frequencies. To do that they should be connected into a Tape loop on your amp. OUTs go to IN's. Then you select the Tape Loop on the amp and that inserts the EQ into the signal path of whatever source you're listening to. It's actions are BEFORE any other amplifier controls such as volume, tone and balance. The EQ itself also has a Tape Loop to replace the one it occupies. Make sure it is not enabled unless you have a Tape Deck on it to use. Choose "SOURCE". The blue LED display is to show you frequencies are present in the program material.

Set all of its lighted band controls at midpoint prior to declaring it defective. EQ is like any spice - a little is good, a lot ruins the recipe.

Mar 21, 2011 | Technics Audio Players & Recorders

1 Answer

MY technics SH-DV290 AMPLIFIER is always in demo mode any ideas about turning it off.


Turning DEMO off
A demonstration of the display is shown if you have not set the clock.
You can reduce the power consumed in standby mode by turning the demonstration off.
While the unit is on:
Press and hold [-DEMO] until "NO DEMO" is
displayed.
Each time you press and hold the button:
NO DEMO (off)9DEMO (on)

The 'Demo' button is on the left hand side of the front panel.

Jan 25, 2011 | Technics SC-DV290 System

1 Answer

Powered subwoofer doesnt work .stopped a couple of months ago.it reads SW on the amp display.sw is turned on -green light on-wiring is all healthy and snug.home theater hasn't suffered any abuse.always...


I sounds like you have blown the woofer. open the unit and check. first disconnect the leads on the woffer, then use an ohm meeter. If you don't have an ohm meeter use a 9v battery across the speaker terminals. If you hear a thunk when the battery touches the terminals the speaker is okay. If tyou don't it's gone. If the ohm meeter reads some number like 4 to 9 the speaker would be okay. If it reads nothing or 000 then it's gone. If you need a speaker you can order it from Pro Line Music 215-736-8055

Jan 15, 2010 | Audio Players & Recorders

1 Answer

Spectrum Analizer lights are not playingor Showing LEVELS.


What model? Does it have a function to kill the display of the SA? Some do.

Apr 20, 2009 | Technics Audio Players & Recorders

1 Answer

Conect eq. with the turntable


hi there, first you have to pit your turntable phono at the pre - amp phono to amplified then after you can put now direct into your equalizer and then to your amplifier

Dec 30, 2008 | Spectrum Technical Hifi EQ-B5200...

1 Answer

Technics sh-eh790 stereo system


Hi there just wondering, if you cant fix your problem would you sell your sound processor as mines broke beyond repair. My email is cocksure001@homail.co.uk.

Dec 30, 2008 | Technics SCEH790 CD Shelf System

3 Answers

Technics SH -8058


the Technics SH-8058 is a beautiful unit, I got one myself for the past 20 years and never failed y EQuing the sound I want.

I am asuming, you got on your reciever TAPE MONITOR... well, the it is simple,

First, just forget about the TAPE on your Techincs SH 5058

Second, on your Technics LINE OUT, goes on your tape monitor LINE IN

and last; on your LINE IN, goes on your tape monitor REC OUT.

Now, choose you desire componet, and turn on your TAPE MONITOR on your reciever...

enjoy and have fun.

Sep 11, 2008 | Technics SH-GE70 Home Equalizer

2 Answers

Technics DV290 system shows "change 1" error


i have a technics sh-dv290 and i need to know how to link the dvd to my tv???
jack

Feb 26, 2008 | Technics SC-DV290 System

Not finding what you are looking for?
Audio Players & Recorders Logo

Related Topics:

90 people viewed this question

Ask a Question

Usually answered in minutes!

Top Technics Audio Players & Recorders Experts

 Grubhead
Grubhead

Level 3 Expert

5699 Answers

The Knight
The Knight

Level 3 Expert

76177 Answers

Marvin
Marvin

Level 3 Expert

85216 Answers

Are you a Technics Audio Player and Recorder Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...