Question about Heavy Machinery

1 Answer

How to change water pump pully on a 580C case backhoe

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 253 Answers

Remove the 4 bolts holding fan to water pump and slip pulley off, replace with new one.

Posted on Nov 04, 2018

Ad

6 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Bill Hackett

  • 383 Answers

SOURCE: The pully on my water pump is lose

The pulley on the water pump is separate from the pump on both the 6 and V-8 engines (you didn't specify which engine was in your truck).
If the pulley is wobbling around and grinding, the bearings have failed on the pump. The fact that it has not leaked is not unheard of. REPLACE THE PUMP! Continued operation will cause the impeller (the side of the pump which moves the water) to chew up the housing. Not to mention leaving you stranded.

Posted on Apr 06, 2009

GIVHRR

  • 72 Answers

SOURCE: 1996 Chevrolet Cavalier, 2.2 Water Pump.Can't remove pully.

USUALLY I LOOSEN ALL OF THE BOLTS BEFORE I TAKE THE BELT OFF TO HELP KEEP THE PULLEY FROM TURNING... USE A LONG SCREWDRIVER OR PRYBAR .. PUT IT BETWEEN THE TWO OTHER BOLTS AND LOOSEN THE 3RD. CONTINUE TILL ALL ARE LOOSE.. IF YOU HAVE ALREADY REMOVED 2 OF 3 BOLTS THEN RE INSTALL THE OTHER 2 A FEW THREADS SO YOU CAN PUT THE SCREWDRIVER IN BETWEEN THEM TO STOP THE PULLEY FROM TURNING.

Posted on May 14, 2009

Anonymous

  • 255 Answers

SOURCE: water pump housing problems

your pump wep hole, bad pump not pep boys fault :( sorry just need water pump.

Posted on Sep 08, 2009

Testimonial: "sound like the problem to me too. they say they put a new pump in but I dought it...."

Patrick Kane

  • 3 Answers

SOURCE: after changed a new water pump,timing belt,idler pully,tensioner for 2004 lexus ls 430, when start engine has a noise look like from pully

COULD BE A BAD BEARING IN THE IDLER PULLY OR THE TENSIONER ON THE TIMING BELT OR THE SERPENTINE BELT. IF ITS A SQUEEL IT MAY BE SOME COOLANT GOT ON THE SERPENTINE BELT. TRY TO WASH THE BELT WITH WATER AND LET DRY COMPLETELY. IF NOISE REMAINS RETURN TO THE SHOP THAT DID THE WORK.

Posted on Jul 17, 2012

dave h

  • 6 Answers

SOURCE: i have a case 580c just rebuilt motor but fuel keeps pouring into motor i changed the seals on fuel pump but it still pours all the fuel back into the engine can anyone help me out PLEASE

i asume it is diesel did u replace the fuel injecter seal??

Posted on Apr 21, 2013

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have installed a new starter on my 580C backhoe When I turn the starter switch it will not engage wheel and just akes a whirring sound Have taken it out and reinstalled it but get the same results


I can talk to you in automotive terms, I know nothing about a backhoe.
I can usually lay the starter motor on the ground, hook up jumper cables properly from starter to battery, at the least, it should kick out the starter drive gear and spin. If it doesn't kick out the drive gear, starter is faulty. I don't know if starter solenoid sits on top of starter motor? I replace as an assembly. Did you check flywheel teeth? I've never worked on a backhoe.

Feb 25, 2017 | Cars & Trucks

1 Answer

Where do I check the brake fluid on a 580C?


I am going to have to guess you are referring to a 580 C Case backhoe.
In any case never ever put anything in a brake fluid reservoir but brake fluid, and the right fluid to be sure, or you will seriously damage or destroy the brakes "forever".
The brake fluid reservoir is usually plastic, and often you can see through it just enough to see the level of brake fluid.
It should be located near the front of the brake pedal, and is usually sort of white in color, with a black cap that can be screwed off.
God bless your efforts.

Aug 04, 2016 | Cars & Trucks

1 Answer

580c case backhoe front bucket is weak and slow goingup


Valves not sealing in the remote control block could be the problem or ram seals.

Mar 12, 2016 | Cars & Trucks

1 Answer

How do i fix throttle shaft leak in Roose Master injector pump on my case 580c backhoe?


there will be small seals or "O" rings in the pump shaft cover. Manual details will be on the net but best if you have a case technician repair it as it will be done quickly and properly.

Dec 02, 2014 | Cars & Trucks

1 Answer

When you change the water pump on a 90 corola 4-door sedan are there alignment marks to get the cams back "in-time" or is there a trick to it?


If you removed the timing belt to fit the new water pump then you have to reset the timing on camshafts/and bottom pully and ... the bottom pully has a mark on gear and casing and the KEYWAY should be dead straight up. and the camshafts have timing marks on the gears and casing behind the cover..
Have fun

Oct 07, 2009 | 1990 Toyota Corolla

1 Answer

Water pump housing problems


your pump wep hole, bad pump not pep boys fault :( sorry just need water pump.

Sep 08, 2009 | Toyota Camry Cars & Trucks

2 Answers

Case 580C Backhoe starting problems


either you have a short in the wiring, a loose connection somewhere or a bad starter, check for broken wires first and clean connections. then try the starter see if it turns with a direct connection to another battery

Jul 14, 2009 | Champion International Garden

2 Answers

Case 580C model 33 backhoe - transmission problems


Pregunta , tienes, el manual de la case 580 ck, donde se muestra el circuito hidrailico de la transmision, si es asi, embiame una foto del circuito o el manual y te puedo apoyar.

Apr 29, 2009 | Ertl 580 Super M Series II Tractor

Not finding what you are looking for?
Heavy Machinery Logo

Related Topics:

316 people viewed this question

Ask a Question

Usually answered in minutes!

Top Heavy Machinery Experts

Brad Brown

Level 3 Expert

18139 Answers

STEVE

Level 3 Expert

34156 Answers

ray gallant

Level 3 Expert

66120 Answers

Are you a Heavy Machinery Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...