I'm getting a code 193 saying my #2 motor is disconnected on my quantum wheelchair. NO wires disconnected how can I fix?

<div><br>The first two red diodes flashing accompanied by beeping on your Quantum 610 electric wheelchair generally indicates a fault condition or an error code. Here are some possible reasons: Joystick Calibration Error: The joystick may need to be recalibrated. Check your wheelchair's user manual for instructions on how to calibrate the joystick properly. Error Code Identification: The flashing lights and beeping may be an error code. Consult your wheelchair's user manual to interpret the specific error code, as different combinations of lights and beeps can indicate different issues. Battery Issues: Low battery voltage or a battery fault can sometimes trigger error codes. Ensure that the wheelchair's batteries are fully charged and in good condition. Motor or Drive System Issues: Problems with the wheelchair's motors or drive system may prevent it from moving. Check for any loose or disconnected wires in the motor connections. Obstructions: Ensure that there are no obstructions or obstacles preventing the wheelchair from moving. Check the wheels and drive system for any debris. Controller or Joystick Malfunction: A malfunctioning controller or joystick can cause issues. If possible, try using a backup controller or joystick to see if the problem persists. Reset the System: Turn off the wheelchair, wait for a few seconds, and then turn it back on. This may help reset the control system. Technical Support: Contact the manufacturer's technical support or customer service for assistance. They may be able to guide you through additional troubleshooting steps or advise on the next course of action. Professional Inspection: If the issue persists and you are unable to resolve it through basic troubleshooting, consider seeking assistance from a certified technician who specializes in mobility devices. Always refer to your wheelchair's user manual for specific information on error codes and troubleshooting. If you don't have the manual, you can often find it on the manufacturer's website or by contacting their customer support. <br></div>

Question edited for clarity and spelling typo.

Error: Brake 1 not connected
Brake 1 error detected
1. Turn power off
2. Disengage then re-engage brake lever
3. Inspect motor connections
4. Turn power on

Error: Brake 2 not connected
Brake 2 error detected
1. Turn power off
2. Disengage then re-engage brake lever
3. Inspect motor connections
4. Turn power on

https://www.google.com/search?q=quantum+Q6+2.0+Brake+error+code+1+and+2

..

Error code 72 on a Quantum 4Front wheelchair typically indicates a problem with the joystick or controller. The best way to resolve this issue is to first try resetting the joystick or controller. Here's how to do it:

1. Turn off the power to the wheelchair.
2. Locate the joystick or controller and unplug it from the wheelchair.
3. Wait for at least 10 seconds, then plug it back in.
4. Turn the power back on and see if the error code 72 goes away.

If the error code 72 persists after resetting the joystick or controller, it may be a problem with the joystick or controller itself and it may need to be replaced.
Please be aware that it's important to follow the instructions in the user manual of the device and only use the recommended parts and accessories to avoid causing more problems.
It's also possible that the problem could be caused by a different issue such as a malfunctioning circuit board or motor. In this case, you may want to contact Quantum customer service or a qualified technician to diagnose and repair the issue

This appears to be a Mobility Power Chair Base rather than a Cellphone question, so I moved the category.

It looks like you may have a loose connector. The error is a brake related error

Error 208
Brake No. 1. Overload: current too high
Brake wiring shorted, or brake defective.
Check motor brake connector.
Check brake wiring.
Check brake resistance.
Replace brake.

https://www.alliedmedical.co.nz/media/6385/qlogic-1-and-2-fault-codes.pdf

and

https://www.google.com/search?q=quantum+600+edge+3%2C+code+208

..

If your Quantum 4Front power wheelchair's leg rest function is not working and stuck in an upright position, it is possible that there is a loose connection somewhere. Here are some troubleshooting steps you can try:
1. Check the power supply: Ensure that the power wheelchair is properly connected to a power source and that the battery is fully charged. A low battery can sometimes cause issues with the leg rest function.
2. Inspect the wiring: Carefully examine the wiring and connections for any signs of damage or loose connections. Look for any disconnected or frayed wires that may be causing the issue. If you find any, try reconnecting or repairing them as necessary.
3. Reset the wheelchair: Some power wheelchairs have a reset button or a sequence of buttons that can be pressed to reset the system. Refer to the user manual or contact the manufacturer for specific instructions on how to perform a reset for your Quantum 4Front power wheelchair.
4. Contact customer support: If none of the above steps work, it is best to reach out to Quantum Rehab customer support for further assistance. They will be able to provide specific troubleshooting steps or guide you on how to get the leg rest function repaired or replaced if necessary.
Remember to refer to the user manual or contact Quantum Rehab customer support for specific instructions related to your model of power wheelchair.

My quantum 600 wheel chair won't work it says system lock ...

www.fixya.com/.../t26033304-quantum_600_wheel_chair_work_says_s...

2 hours ago - My quantum 600 wheel chair won't work it says system lock -Wheelchairs question.

Pride Mobility Quantum Q6 Edge (Power Wheelchairs ...

www.usatechguide.org/itemreview.php?itemid=1626
Quantum 6000 or 600 Rehab Power Wheelchair - CareCure Communitysci.rutgers.edu/.../showthread.php?...Quantum-6000...Rutgers UniversityJul 4, 2008 - 10 posts - ‎9 authorsI had the QUANTUM 600e Rehab Power Wheelchair for six months. ... C-500 Hvy dutypower chair w/hi-speed motors, power seating system, .... I have a Q600 with tilt, recline, leg extension, Q-logic..pretty much the works. ... the thing shuts itself off andwon't move when I have anything under 90% charge?Quantum® 600 Power Chair Reviews - Pride Mobilityownersclub.pridemobility.com/reviews/item/1/20The Quantum® 600 Power Chair delivers the stability of patented Mid-Wheel 6® ... At that same time the 3rd motor set was changed my seating system was ... We were rescued by boat and my friends say the wheelchair was working ... Insurance won'tcover a power chair for me yet so I had to pay out of pocket for this one.

On a power chair I would check all plug connections on motors. Check resistance of brake coils and compare with each brake. If you have the error code I would check the manual that comes with the diagnostic box.

How can i fix break #203 and 204 disconnection problem on quantum 6000 wheelchair. Thanks

check wires

I had a 203 and 204 error "brake disconnected " ,engaged both motor lock pedal , problem fixed