Question about Kenmore Washing Machines

1 Answer

What is causing my Kenmore model 110.28322700 timer to not work correctly ?

When I put it on a 14 minute wash it doesn't allow any water into the washer but when I move the timer up to 12 minutes it fills up the washer & it starts washing plus it goes through the rinse cycle like it should. Everything is fine except for when it's on the 14 & 13 minute wash cycle. I'm thinking the contacts are bad in the timer. Does anyone know for certain ? Thank You

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • Kenmore Expert
  • 227 Answers

Yes you need replace the timer

Posted on Apr 11, 2018

Ad

6 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Dov Dror

  • 641 Answers

SOURCE: No pressure to drive swing arm.

Check first that no debris is blocking the holes in the spray arm where the water comes out, and clean out the holes. In case it will not solve your problem, it's look like a pump problem (the pump has two functions : drive water to the spray arms and to drain water out the washer). Open the rear panel and listen if the pump works during the wash cycle. In case it doesn't work, it should be replaced. Good luck !

Posted on Jun 20, 2006

catriver

Ron Marek

  • 878 Answers

SOURCE: Wash cycle not working...

Kerbri, it sounds like your pressure switch could be the culprit. Under the top console the switch will be on the left side. There will be a clear tube that runs from the tub to the switch. Take another piece of tubing about the same size in diameter, disconnect the tube to the pressure switch and connect the tube. Blow into the pressure switch and see if the washer starts agitating. If so, replace the pressure switch.. Another thing to check would be the harness to the motor, make sure it is on tight. Good luck

Posted on Jun 28, 2006

larryyb

Larry Youngblood

  • 291 Answers

SOURCE: washer does not get out of the wash cycle

replace the timer

Posted on Nov 24, 2008

BOYNISMO

  • 120 Answers

SOURCE: Kenmore washing machine model 110 wash cycle stops

DOES IT DO THIS ON EVERY WASH OR SOMETIMES? IF SOMETIMES, CHECK LID SWITCH( THERE'S A LITTLE HOLE WHEN YOU OPEN THE LID, ON THE LID SHOULD HAVE A LITTLE PLASTIC PIECE THAT GOES IN THAT HOLE. THE SWITCH IS UNDER, INSIDE THAT HOLE. YOU CAN GET A PEN OR KEY TO SEE IF IT'S BROKEN.)
\
BOYNISMO@YAHOO.COM

Posted on Aug 21, 2009

Anonymous

  • 998 Answers

SOURCE: My Kenmore 80 series top

clean inlet valve screens

Posted on Aug 25, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

MY KENMORE WASHER , MODEL # 20712 991 70 SERIES FILLS WITH WATER AND NEVER GOES IN THE AGITATE MODE , IT JUST CONTINUES TO FILL(it would run over if allowed), WHEN YOU MANUALLY MOVE THE TIMER TO THE SPIN...


The water level sensor hose may have come off. This would require some dis-assembly to repair. Get the correct model number please to get a diagram.

Aug 07, 2011 | Kenmore Washing Machines

1 Answer

I have a Kenmore/Whirlpool Washing machine model 110.26832691 that doesn't allow hot water into the tub. I have put a new timer as well as a new temperature switch. Any answer?


Hello

Please try to swap both the connections, hot to cold and cold to hot, swapping will hopefully work. If swapping wont work then the water inlet valve also known as inlet hose assembly is bad and needs replacement. Please check the water level switch as well although I believe it is the water inlet valve causing this problem.

Kevin

Nov 11, 2010 | Kenmore 3.2 cu. ft. Plus Top Load Washer

1 Answer

Timer only works on heavy cycle not on normal model #11024632300


Could be a bad timer or loose contacts.
Unplug the washer.
Open the control console.
Remove the wire harness connector from the timer and re-insert it.
Also advance your timer manually 360 degrees around several times. This can cause stuck contacts to work correctly.
If this does not correct your problem you will need a new timer.

Feb 14, 2010 | Kenmore 24632 Top Load Washer

1 Answer

Model 110 stops with water in machine. Move dial to rinsing cycle. Runs some then stops with water in machine.


HI. The timer module will be the culprit here. The timer motor is malfunctioning. This motor is responsible for the forward motion of the timer dial. If it dose not function correctly, it will cause the issues that you are experiencing. kindly replace this damaged timer control device. Once replaced, the unit will operate properly.

Nov 27, 2009 | Kenmore Washing Machines

1 Answer

Kenmore washing machine 110.22082 does not drain


you probably looking for a new drain pump ( control board also possible)

Sep 05, 2009 | Washing Machines

2 Answers

Top loading kenmore washing machine frozen water loaded


Could it be that it has overheated? My mom's washing machine isn't a kenmore, but it has a mechanism that causes it to stall when it is overheated from constant use. After about 15 minutes it cools off and starts again.

Aug 07, 2009 | Kenmore 24032\24036 Top Load Washer

Not finding what you are looking for?
Washing Machines Logo

Related Topics:

60 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kenmore Washing Machines Experts

fordexpert

Level 3 Expert

5692 Answers

Harvey Mahal

Level 2 Expert

39 Answers

Kristen Denison
Kristen Denison

Level 1 Expert

13 Answers

Are you a Kenmore Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...