The handsets are displaying 'UNREGISTERED' and not working!

Could you please tell me what the model is

Up to 6 handsets can be registered with the DECT 1480 phones. I have the 5 phone unit and needed to add the 6th phone. All I got was "Searching" in the display and the battery wouldn't even charge!

So here's what you have to do to get additional phones (up to 6 units) to work with the base. If you can get past step 1, it's a snap...

Step 1: Place a charged battery in the handset. This could be a problem if all your handsets are not registered, since unregistered phones don't charge (who thought of that design?). What I did was SWAP the battery from an already registered and charged phone with the new unregistered phone.

Step 2: Here's where the magic happens. Press the 'END' and '#' keys simultaneously... hold them down until a System Reset menu appears. Select "Deregister HS" and press Menu.

Step 3: Now, do the same thing again (hold down END and #), but this time select Base Unavailable and press Menu. You will see Base Unavailable Yes/No... Select Yes. Then place the handset in the base, wait a few seconds, and Voila!. it's registered. You can even change handset numbers using this menu if you play around with it.

Thank you, helpful employee at Costco for supplying the magic code. And hey there, UNIDEN... including this in the operation manual would have saved many customers much grief with de-registered phones!

Enjoy!

1. Place the unregistered handset on the charger.
2. Press and hold the FIND button for 4 seconds on the base.
3. Release the FIND button once the IN USE light starts to flash.
4. A confirmation tone will sound when registration is successful. Handset X is displayed where X denotes the number of handsets. The phone will then go back to idle.

just in case you need it:

User Manual Clarity D613C Combo Pack (D613 with D613HS)

Don't forget to rate if this was helpful :-)

same problem here T.T really urgent

CLICK HERE for your owners manual in PDF format.
CLICK HERE for the troubleshooting section.

"BUSY" in the display means -

*The called handset is in use.

*The handset you are calling is too far from the base unit.

*There is no handset registered to the base unit matching the extension number you entered.

*Other units are in use and the system is busy. Try again later.

Remove the batteries form each handset.
Replace them one at a time and check for proper operation.
One may have become unregistered when a battery died - or power outage.

See page 35 of the manual to un-register and re-register them to the base.

Thanks for using FixYa - if you require further clarification, please use the "Continue With This Expert" option so we are connected in the future.

Thank You :D

SOLUTION:

1. First, remove the battery cover on your unregistered TCX905 and look under the battery to confirm that you indeed purchased a TCX905 because some Uniden handsets were packaged as 905's but were not.

2. Take the fully charged unregistered 905 to the base unit TRU9496.

3. On the TRU 9496 base unit press "Menu" then select "Registration" and press OK

4. You should get the message "press the # key on the remote handset".

5. Depress the "#" key on the unregistered 905 and it should register.

IF YOUR HANDSET WAS WORKING AND THEN STOPPED WITH "UNREGISTERED":
If lowercase unregistered is in main display and a reg. appears under the left soft key:
Press the left soft key below REG. and then press and HOLD the button on the top of the base station until the two indicator lights on top of the base station turn off. Wait until handset signals with beeps and registered. You are done

THIS IS FOR FRESH OUT OF THE BOX REGISTRATION OF UNREGISTERED HANDSET
Press REG Register shall be highlighted.
Scroll to Register. Press Select.
Enter the system PIN (Default: 0000). Use
CLEAR to correct typing errors.
Press ENTER to confirm.
• Your handset starts searching for the base.
Press and HOLD the round button on top of the base unit until the two
indications turn off.
• If registration is successful, the signal icon

On you base between Clear and intercon push middle button, with erow push display base -ID

I just successfully registered 4 TCX905s with my TRU8865 base - it's documented in the TCX905 manual.

Be sure the handset you want to register is fully charged.

Remove the handset you want to register from its charger.

Now unplug the AC for the main base, hold down the 'find handset' key on the base and plug the AC in again, when it beeps, you can let go of that button.

Hold down the '#' on the handset you want to register, it will show 'Registering Handset...' and when it beeps, it's done - registered, you're good to go :)

Uniden TRU8885-2 Cordless Phone > User Guide E X P A N D I N G Y O U R P H O N E w w w . u n i d e n . c o m Register the Handset to the Base If you purchase an extra handset, you need to register the handset to the base before use. Only one handset can be registered at a time. The handset ID for the supplied handset(s) was assigned at the factory, which has #1 or #2 in the display (#2 for models that have two handsets in packaging). When you register additional handset to the base, the handset ID will be assigned. 1) Before registering the extra handset, the battery pack must be charged for 15-20 hours. 2) Place the extra handset in the main base unit to begin registration. 3) While the handset is registering, Handset Registering will appear in the LCD. When Registration Complete is displayed, the handset has been registered to the base. If Registration Failed appears, please try these steps again. Extra Handset Extra Handset Charger Charger Main Base Extra Handset + Main Base Charge the handset for 15-20 hours. Place the extra handset in the main base to register. 1 2 3 4 ?An extra handset can be registered when the main base is in standby mode. ?Standby Mode - The handset is not in use and talk/flash has not been pressed.