True bolt change 4 dig. Code on my door lock - Locks & Locksmithing

Question edited for clarity.
Question moved to home Security - Safes.

You can't. You have to open the safe with the Emergency Key, the combination Dial or in your case with the Electronic Keypad.

STEP 2 - CHANGING THE USER CODE
1-Open the safe by following step 1.
2-Press the Green set up button (Located on the
back cover or the hinge side of the back door
cover), the LCD display will turn Blue.
3-Enter your new user code (1-8 digits).
4-Press the # key.
5-The LCD display will turn Blue and show IN.
6-The LCD display will briefly show your new code.
7-Your new user code is now set to open the safe
NOTE: It is highly recommended to leave the
safe door open and practice your new code
several times before closing the door.

Manual

https://www.manualslib.com/manual/1800698/Amsec-Dl4000.html#manual

..

question edited for clarity and removal of text message abbreviations :>)

So the girlfriend got inside first and took all the good stuff and left the door open with the locking bolts out and deployed? :>(

Page 3 of the manual. You press the red reset button and change the pass code to a new one. Change the batteries as well at the same time. This is the better manual. Other left below

https://docplayer.net/40344439-7803-paraguard-deluxe-electronic-digital-safe.html

INSTALLING BATTERIES
Open the battery compartment cover located on the inside cover of the door. Install the batteries as shown on diagram (4 AA
batteries). Close the battery compartment cover.
SETTING AND CHANGING PERSONAL CODE
1. Open the door and press the red button at the rear of the door. The yellow light will flash.
2. Set a personal code, input a 3-6 digit set of numbers.
3. Press "
*
" or "
#
" to confirm.
The yellow light will turn off, indicating the code was entered successfully.
Use the same procedure to change the code.
4. Test your code before closing the door.
USING YOUR PERSONAL CODE TO OPEN THE SAFE
Input your 3-6 digit personal code then press "
*
" or "
#
" to confirm. When the green light flashes, turn the handle clockwise to
open the safe.

OPERATING MANUALS

https://images-na.ssl-images-amazon.com > images
PDF
Thank you for choosing a Paragon Lock and Safe product. Paragon Lock and Safe (PL&S) warrants the ... www.paragonlockandsafe.com for return instructions.

• 
  

  83-SAF7751/7751 Deluxe Wall Safe Keypad

  https://images-na.ssl-images-amazon.com > images
  PDF
  Paragon Lock & Safe ED keypad operating manual. ------------. -------- ... 83-DT5919/7803 ParaGuard Deluxe -----. 83-DT5910/7501 Paragon Rifle Safe----.

1. Enter the factory Entry Code
2. Press 1. BOLD CIRCLE LOOKS LIKE A PERIOD on the keypad within five seconds.
3. Enter your personal 6- dig et code. You must enter each number within 5 seconds of each other.
4. Press 1.large dot ...
5. The door will lock and unlock to confirm that you have successfully programmed a personal entry code.

Walld"

Best thing to do is to just rest the blade teeth against a peice of scrap wood, and use the allen key/spanner to undo the bolt. As the bolt undoes in the direction of the cut, the blade teeth should dig in and stop it turning. If the blade lock isn't working anymore, it could mean that it has broken inside, so be careful, incase there is a bit of loose metal in the gearbox, it will be quite catastrophic if it gets caught in the gears.

there is usually and access cover on the bottom right behind the oil pan, the bolts are on the back of the flywheel. This is true with most automatics but if it is different I know a guy who has changed these out before that I can ask.

Do this, with the door open:
Remove cover from assembly by sliding cover up and off. You will then see the program button.
A programmed code can be from four (4) to eight (8) digits long.
Up to 2 user codes can be entered.
Excess delay in the programming steps once started will cause unit to beep twice and will require you to restart from step (a).

Programming the first User Code:
a. Press the program button on the interior unit once.
b. Enter in 4 to 8 digit code onto the keypad.
c. Press the "LOCK" button to save code.
d. Extend the bolt by pressing the "LOCK" button and re-enter the code to test. The bolt should retract to the unlocked position. If it does not unlock, repeat steps (a) through (c).

Programming the second User Code:
a. Press the program button on the interior unit twice.
b. Enter in 4 to 8 digit code onto the keypad.
c. Press the "LOCK" button to save code.
d. Extend the bolt by pressing the "LOCK" button and re-enter the code to test. The bolt should retract to the unlocked position. If it does not unlock, repeat steps (a) through (c).

After programming in just one new code, the existing old code may still work. I suggest that if this is the case, that you program in two codes to make sure that the old one is over-written. You may try programming in the same new code both times if you don't want to have two codes.

Here is a link to the installation and programming instructions that I excerpted the reprogramming instructions from:
http://s7d5.scene7.com/is/content/BDHHI/kwikset-smartcode

For further assistance or warranty information: call 1-800-677-5625 USA & CANADA
or visit, www.kwikset.com

Good luck!

You are programming it correctly. If you are sure the battery is good I think the keypad has simply failed.

Enter correct code:
Hold down release on front & enter new 4 dig code & let go of release and new code is input.

Try pulling or pushing the door in while you lock and unlock, sounds like the bolt is binding in the door frame, comon problem with these locks in changing temperatures and humidity.

Enter this code #43574357* and device information comes up. Choose system information. Use the last 4 digits of the MDN OR MIN (they should be the same) for the lock code. When the phone is unlocked, you can change the NAM back =)