I have a Lifespan Torque II treadmill coming up with a E03 error message. What do i need to do to fix this?

1. Power OFF and ON.
2. If the error is still shown, turn the treadmill OFF and unplug from the wall outlet. Find the cable that goes between the board under the motor cover and the console. Unplug any connections and replug.
3. If the error code is still shown please contact customer service.

http://www.fixya.com/support/t12506455-lifespan_fitness_focus_treadmill_e03


Unsure if this solution worked or not for prior FIXYA question.


Lifespan fitness focus treadmill E03 error

What Does Your Treadmill's Error Code Mean? - LifeSpan

www.lifespanfitness.com/.../what-does-your-treadmills-error-code-mean

Free
May 21, 2015 - If the running belt stops after 6 seconds of starting the treadmill, this may indicate that either the ... If there is no belt movement, or you notice a burning smell coming from the motor area, this ... An E6 or E7 error code is an incline error code. ... This will cause the incline motor to raise the running deck up.

[PDF]ERROR CODES: ADDITIONAL ERROR CODES:

www.gympart.com/TSB/.../Treadmills/.../Sportsart%20Error%20Codes.p...

ERROR 6: INCLINE ERROR - CHECK INCLINE OPERATION AND CALIBRATION. ERROR ... ERROR 1-1: AC SERVO ERROR - AC SERVO MOTOR ENCODER HAS FAILED ... error codes listed by category: treadmills, bikes, elliptical trainers. ...ERR1 Condition 1: Press speed key; walk belt doesn't move; ERR1 appears.

[PDF]Error Code Troubleshooting Guide

Replacement Parts for Fitness Exercise Equipment at SPORTSMITH

Precor Error 03, Memory, RAM, EEPROM Test Error Probable Cause This error message almost always indicates an upper PCA problem when it is consistently displayed. Failures causing this error message to be displayed are rare.
Corrective Action If the error message is consistently displayed when the unit is powered up, the upper PCA should be replaced. It is possible to see this message displayed intermittently due to external causes. If the units A.C. input significantly dips during the power up test sequence the test could fail resulting in this message being displayed. Treadmills operating on non-dedicated A.C. circuits may see this message displayed on an intermittent basis.

Precor Error Code 03 E03 EEPROM Test Error

Hello

yes, your correct this could be the lower board with the issue.
The lower board could have blown a fuse, which you can check and replace quite easily. If the fuse is good look for other burnt spots on the board. The lower board may need repairing/replacing.
If the machine stopped while in use (after about 10min) then you will have a few other problems to check. Try adding silicone spray under the belt and if this has already been done then the running belt may need replacing.

E1 is never a good thing...

gymWorld.net.au

Precor Error 03, Memory, RAM, EEPROM Test Error Probable Cause This error message almost always indicates an upper PCA problem when it is consistently displayed. Failures causing this error message to be displayed are rare.
Corrective Action If the error message is consistently displayed when the unit is powered up, the upper PCA should be replaced. It is possible to see this message displayed intermittently due to external causes. If the units A.C. input significantly dips during the power up test sequence the test could fail resulting in this message being displayed. Treadmills operating on non-dedicated A.C. circuits may see this message displayed on an intermittent basis. Precor Error Code 03 E03 EEPROM Test Error

please proceed according and fix it. God bless you
trouble +cause+ solution

E6 Faulty Safety key Check Safety key or switch
Elv. Motor not moving Check Elv. Motor
connections
Elv. Motor screw binding Clean screw, lubricate or
remove obstruction
Elv. Motor out of range Check motor zero position
Elv. Potentiometer Calibrate elevat ion motor

Dear Sir>
Whatever error proceed 1) Adjust the speed sensor, see the diagram, clean, and tight the wires connector very well.
2)Test the input voltage motor, if there are the motor need repair.
3)Test the output voltage board, for input voltage motor, if there are Not the board is faulty.
4) After your fix it RUN the software calibration for diagnose, and troubleshooting in according with instruction manual.
See my personal TIPS for help
God bless you

repair the magnet wire, adjust the magnet and reset see the diagram attached.Clean it.
sincerely. God bless you