Jenn air oven problem

It's faulty and in some sort of self protect mode. You need a service call or you can try some of the fixes here.

FIXED - WW2780 Jenn-air oven keeps shutting off ...

www.applianceblog.com > mainforums > threads > ww...

Feb 15, 2012 - Hi.... I have a Jenn-air oven model WW2780 that keeps shutting off after being turned on, almost always during the preheat. From what I have ... Missing: WW27430P ‎' Must include: WW27430P

Jenn Air Range Stove Oven - Oven Won't Turn Off - Repair ...

www.repairclinic.com > RepairHelp > Jenn-Air-Oven-...

Here are the most common reasons your Jenn Air oven won't turn off - and the ... Enter model number to search for the required part specific to your product.

HOW-TO: Jenn-Air Oven WW27430P Door won't close

www.appliancepartspros.com > repair-help > ww27430...

Door won't close is the most common symptom for Jenn-Air WW27430P. ... I have a Jennair jjw9630cas double wall oven, and after a few years I noticed that the light would not go out, first in the bottom ... Door pulls shut and li8ght stays off.

HOW-TO: Jenn-Air Oven WW27430P Won't start or doesn't start

www.appliancepartspros.com > repair-help > ww27430...

How to Replace Oven Temperature Sensor Kit for Jenn-Air WW27430P Won't start # ... Jenn Air stove JDS9860CDB00 error code 1d11 oven not shutting off. ... Very easy on this and other models with this sensor-- just two screws holding it in ... Rating: 5 · ‎123 reviews

..

The F3 means there is something wrong in the sensor circuit, sensor/wiring/clock. F3 Problem: Shorted or open oven temperature sensor (RTD): Solution: Check sensor harness and harness connection between oven sensor and oven control. Replace oven temperature sensor (RTD) if wiring is ok.

check to see if you have a fuse blown to your stove and replace it

From JENN AIR FAULT CODES...

FC - Communication error between boards - Wiring harness or power relay board (PRB)

Hope helps.

just finished cleaning and FC comes on and wont stay off. constant beeping

We own a Jenn-Aire model W27400W oven. The display module has gradually gone dim over a period of several months prior to the end of the warranty, and the display is no longer visible. It is apparent that several Jenn-Aire oven models use the same display. Does Anyone else have the same problem, and If so, are they willing to join a class-action suit against Jenn-Aire with us?
Steve Patterson
303-256-8494
[email protected]

I posted a message on 12/27 and since then I have contacted Jenn-Air again and as I mentioned above the two things they told me to do didn't work, so I looked at the schematic of the unit and there appears to be a motor that locks and unlocks the door. I have a service repair coming this Saturday and seems to believe the motor is bad. Trenatru are you getting an error message? I was told by Jenn-Air that there is a 6 yr. warranty on electrical parts so will try to keep you posted if that is the cause. If you havn't tried shutting off the power try that first. They said keep it off for a couple minutes before turning back on. If that try pushing on the door and hitting cancel twice. If those two things don't work, will let you know what I find out next weekend.

How do I clean my jenn-air double oven when I lock oven door and turn oven to clean mode set time to start I don't get anything. Also when I lock the oven door the oven lock light does not come on.

Most likely its the EOC (electronic oven control), it needs to be replaced. If you self cleaned the oven a lot the very high heat generated fatigues computers in modern ovens.

Try http://www.applianceaid.com/fault_codes.html