Question about Boating

1 Answer

How to drain remote control bass boat only used 15 min. ran good until water got in the hull don't know how to drain it

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 331 Answers

Install a bilges pump maybe??
Look if there is no plug installed at the lower edge of the transom.

Posted on Nov 14, 2017

Ad

6 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Anonymous

  • 1 Answer

SOURCE: Wired remote bass control knobs

I'm wanting to know the same thing... But be careful on the pin out of the control you get.

I have an audiobahn 2300HCQ amp... Before I had the 1800. The 1800 came with a remote with 6pin remote cord. I got the 2300 used and did not get a control for it. The plug on the 2300 is a 4 pin plug... I can't figure out how to cross it over correctly to get the 1800 remote to work on the 2300.

I have tools to crimp an end... Just can't figure out the color pin out.

Posted on Sep 15, 2008

Anonymous

  • 1 Answer

SOURCE: I have a new EP Rashing Boat NO. 7000 (remote control) that won't run. I have charged the boat battery and have new batteries installed in the controller. On switches are on. Is there a way to chec

hello!Most ep boats need to be in water in order for it to run.you say te model is 7000 ,who makes it? NQD....?

Posted on May 07, 2009

Anonymous

  • 93 Answers

SOURCE: remote bass control short

It Could be Eiher Problem Make Sure The Remote our using is thew same brand as the amp its plugged in to

Posted on Jun 14, 2009

smarthome2

Frank Fulton

  • 1114 Answers

SOURCE: How do I use the remote to cont bass & treble for rxv-657 reeiver

No, Tone controls are on the front of the unit only. If your passing video thru the unit you can go into the setup menu from the harmony and adjust all the sound parameters that way "on screen" The only "EQ" capabilities are for the Center channel only. You can adjust "speaker size". "Large" setting will give you a little lower response. "Small" will crossover the speaker at "100hz" That's about as far as tone adjustment goes on this unit. Hope this helps

Posted on Jul 01, 2009

pabloloco

Paul Sager

  • 2335 Answers

SOURCE: remote code for commtel control freak remote.

I can help you with your URC-3021 Universal Remote Control issues.

I do not see a listing for Alba TVs in the Urc-3021 Code List.

But don't give up; many manufacturer's re-use other's control codes.
Therefore, I recommend using the One For All URC-3021 Code Search, feature to find the compatible codes to control your device.

I hope that helps.
_______________________________________________
Reassign URC-3021 Device Key
Urc-3021 Code List Download
One For All URC-3021 Code Search

Posted on Apr 26, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What can i do to stop the flashing of the depth finder at times it will not show the current depth


Hey Joe,
Wow.. where to start.. there are so many things that will cause the issue you are describing.What type of electronics do you have? Does this happen at all speeds? Where is the transducer mounted? I need more info about when it stops reading.
1.Wrong setting on the unit
2 Bad transducer
3 Bad transducer mounting (either inside the hull or outside the hull.)
4. (In hull) Turbulence going under the boat (mine quits reading at about 55 mph @ half trim...the boat is lifting so much it causes air pockets so the transducer loses contact with the water)
5. (Outside hull) Turbulence around the bottom of the boat where the transducer meets the water.
Good luck,, when you get the info.. reply to me..

Jun 03, 2017 | Boating

1 Answer

Where are the drain plugs situated on a T Cat boat


has to be out on the rear hull area
below water line or deck platform
upgrade hull with
aftermarket stainless steel or brass systems

wise to have a bilge pump
and carry bailing buckets

9f16875a-8021-465a-81f2-8f6b06be53e4.jpgindex-cvxygyvu0vydc25j522ljeey-4-2_0.jpgst-cvxygyvu0vydc25j522ljeey-4-3.jpg

Mar 31, 2017 | Boating

1 Answer

Why does. My boat sit low in the water when i stop to fish it's. A1989 Cajun. Bass boat??????


physics.
As you go through water at any speed the force of the water flowing/being forced beneath it will cause it to rise in the water. When you are stationary there is no pressure applied to the hull. If your boat carries ballast removing some will mean that it displaces less water and will sit higher in the water when stationary.

Archimededs on water displacement?




http://en.wikipedia.org/wiki/Archimedes%27_principle


Jun 10, 2015 | Boating

1 Answer

Water in hull of bass tender pro


Find the leak and patch it. Use a good marine epoxy system with a sheet or two of fiberglass cloth laid-across the crack. Be sure to sandpaper the area thoroughly with rough paper. If you can't find a leak or crack, fill the hull with water and inspect for leak. Repair after.

May 20, 2014 | KL Industries Basstender 10.2 Fishing Boat

1 Answer

The water will not drain from a GE spacesaver on my boat


If the outlet on the space saver is lower than the outlet on your boat drain outside the hull it won't drain.

Oct 16, 2013 | GE Washing Machines

1 Answer

What problems or benefits will I get with an aluminium boat hull


Aluminum boats are easier to maintain, will last longer than fiberglass, and are easier to repair. You can also bump into things without causing damage like you would to a fiberglass hull.

The only real advantages to fiberglass are that it looks better due to the gelcoat finish, providing that it is maintained, they also feel more solid in the water due to the extra weight, and they tend to ride better and are quieter than an aluminum hull.

One other consideration is whether you will operate it in fresh water or salt water. Salt water can lead to corrosion problems on an aluminum hull if you leave it in the water. Fiberglass doesn't have that problem, but you can have a problem with blistering if you leave a fiberglass boat in the water for long periods, especially if you don't use a bottom coat of some sort.

If you do opt for an aluminum boat in salt water, just make sure that you spray it down with fresh water and wipe it down with a soft towel whenever you take it out of the water. This is actually a good practice for any boat, aluminum or fiberglass.

Mar 28, 2013 | Boating

1 Answer

Transducer is throwing up a large Rooster tail.I installed it to instructions


Might help to tell us what kind of boat - deep V hull 22 ft.? bass boat with shallow V hull? Some need the transducer closer to the centerline of the vessel while others do better more outboard, Naturally they need to be flush with the hull no matter where they are located. Depending on the transducer, you could also try properly mounting it inside the vessel near the transom. Good new is you are getting good info from it. Cheers Pete

Nov 16, 2017 | Humminbird 586c

1 Answer

Can hear water in the hull; is there a quick drain and where is the most likely area it is leaking from, is there a kit? model H27.


in the nose of the boat right next to the handle theres a funny looking switch if you stand the boat on its nose and flip the switch it will let the water out.
But...in my personal opinion it keeps the hull a little lower to the water and the paddles deeper...

Feb 04, 2010 | RTO Pelican Monaco Pedal Boat

2 Answers

Motor fires off great and run good but at full speed after 15 mins it dies and won't start after 10mins it will start but at hight speed only after i get it going run good at 1/2 speed


What Year? Have the coils checked, they are located under the flywheel, some have been known to act up over time due to heat because of age. They time between dieing and restart souns like they had time to cool off until overheating again

Apr 17, 2009 | Light Outboard Motor Boat Bass Fishing...

Not finding what you are looking for?
Boating Logo

Related Topics:

101 people viewed this question

Ask a Question

Usually answered in minutes!

Top Boating Experts

ray gallant

Level 3 Expert

66248 Answers

Andrew Taylor
Andrew Taylor

Level 3 Expert

30467 Answers

Tom Chichester

Level 3 Expert

55370 Answers

Are you a Boating Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...