DVD player does not work with Verizon FIOS set up help LC-37GD4U want telephone not email assistance Mary Jo

found the problem after reading a post on this site. Last thing I used was DVD player so disconnected DVD Sony player, followed the factory reset instructions and now the volume works normally! It was the DVD player. Thank you so much for the info and lead. The problem is DVD not TV,

Jul 20, 2014

Hi,

Due to certain limitations of the Panasonic DMR-EH75V, it can only accommodate composite Video INput and give composite Video OUTput as well as the standard Audio L/R. Additionally, if your Verizon FIOS HD cable box has an RF OUT, that can also be connected to the RF/CABLE IN of the Panasonic.

Please refer to the simplified diagram below.



Hope this be of initial help/idea. Pls post back how things turned up or should you need additional information.

Good luck and kind regards.

Thank you for using FixYa.

1099 works for one for all remotes

I have the Samsung Sound Bar WS1R model. I tried all of the Samsung codes; TV, audio receiver, and audio amplifier. The DVD code 3918 worked for my Verizon FiOS remote. Program it to your AUX button and it will control the volume while your other buttons; channel, menu, etc work the set top box. I hope it works for you too!

Check the connection cable. If the Verizon box and the DVD player are connecting to the same TV input, ensure that the Verizon fios box is connecting to DVD input, and DVD output is connecting to TV.

If you connect DVD out to Verizon box input, and then TV , you will have to turn off the receiver box to see DVD.

If you use only one TV Input connect Verizon output to DVD input and DVD out to TV.

If instead you use separate inputs on TV, then try using the source/select input button on TV remote, and try different cables.

Regards.

Hi

You can reprogram it by following these instructions--

Power turns on or off both your STB and TV when you are in STB mode. (If you have a DVR STB, the DVR will continue to record scheduled programs when off.) However, you can reprogram how the Power Key works. If you want the Power Key to control multiple devices at once --

1. Press and hold the STB key.
2. While holding down the STB key, press OK.
3. Release both keys. The Device Keys will blink twice.
4. Press 9 - 7 - 7. The STB key will blink twice.
5. One after the other, press each Device Key you want the Power Key to control, in the order you want them to turn on or off. Each selected device Key will blink twice after it is pressed.
6. Press OK when done. The STB key will blink three times to indicate success in programming.
For example, to program the Power Key to turn on or off your TV, AUX and
STB, in that order with one press of the Power Key, press [STB+OK], [9-7-7],
[TV], [AUX], [STB], [OK].

These are the codes for GO Video DVD Player--

Go Video 0771, 0768, 0810, 0896, 1071, 1102, 1185, 1757


You can view/download the manual for the fios from this link--

Verizon fios remote programming

You can visit this link for more information--

Verizon FiOS Troubleshooting

If you want to doanload the user manual for your verizon set top box you can get it from here

Please do accept this solution and revert for further assistance.

Thanks
Rylee

This is the setup for the 6416 and the vcr.

Go on the Verizon website and request a new remote, the Verizon P265 Remote model. It will have all the newest firmware and it should have the code. I know this because I had a TCL 32" TV and the code wasn't on my old Philips RC 1445302 model. TV and new remote are "talking" just fine now. Verizon won't even want the old one back.

please provide more deatial. i am a verizon fios tech and im willing to help you.

go to verizon.com and look up fios tv and then from there go to installation and then troubleshooting