How do I set time on Advance model 4093 digital clock?

Sounds normal. Most digital clocks have a rapid set in forward and a slow in backwards. Helps you to get through the hours quickly. As you speed past the correct setting, you then backup slowly to the correct time.

Press and release Time. Press and release each number of the time: if the time is less than 10:00, start with a 0, otherwise start with 1. Press and release the PM button if it is afternoon. Press and release Enter. Press and release Alarm, then press and release Time to confirm it is set.
(Took me forever to figure this thing out)

Hello
HERE is the link of Alcatel web site, you can get help from there.
good luck

There are many LaCrosse atomic clocks. Which model do you have? Support for most is available here: http://www.lacrossetechnology.com/support/home.php . Use the drop down menu to select the model.

For the analog clocks, there is a manual set button on the back of the clock. Press the button and wait for the clock to advance to the correct time. Then make sure the correct time zone button has been pushed. Then make sure the clock is in a location where it can hear the signal overnight. (For best results stand the clock upright in a window.)

For WT-2165U travel alarm, press and hold Set to enter the setting function. Then select the time zone (with + or -) then press and release Set. Set the DST setting to on or off as needed, then press and release Set again. The next setting option is the snooze alarm duration. Press and release Set again to change the hour manually (+ to increase). Press and release Set again to set the Minutes. Correct the date (year, month, day, day of week) similarly. Then set the display to 12 or 24 hour time. Press and release Set to finish and exit the set functions.

For some of the digital clocks you can set the time manually by pressing and holding Set. First set the time display mode (12/24), then press and release Set again. Then set the hours, followed by Set and then the minutes. Continue through other menu options or just do not press any buttons for several (30) seconds.

On the digital clocks, the item being changed will flash.

To avoid interference with the signal reception, place your radio controlled clock where it will be at least six feet away from a TV, computer, air conditioner or other household electrical appliances. The optimal location is near a window. Windows facing Colorado providing the best signal.

I hope this helps.

Cindy Wells

Hi bowingman,

To use 12- or 24-hour time for your watch, please follow the instructions below.

1. Press and hold the "Set" button for 2 seconds. The "Set" button is on the lower right side.

2. Press the "Date Advance" button on the upper right side. This will reset the seconds.

3. Press the "Change Mode" button on the lower left to set the hour. The hour will flash. Press the "Date Advance" button until the correct hour is displayed.

4. Press the "Change Mode" button again to set the correct 10s unit (first digit 1 or 0) for the minutes. Press the "Date Advance" button until the correct first digit of the minutes is displayed. Repeat this step to set the second digit of the minutes.

5. Repeat Steps 1 through 4 of this section to set the year, month, date and day and whether to use 12- or 24-hour time for your watch.

6. When finished, press the "Set" button (on the lower right) to return to the current time view and lock in your settings.

Hope it helps.

Thank you for using FixYa.

SELL! SELL! SELL! Yup the clock has bit the dust sell er and cut your losses.

Setting the Clock:
When the coffeemaker is plugged in, 12:00 will
flash continuously until you set the time.
Entering “Time Set” Mode:
To set the time, hold down either the “Hours”
or “Minutes” button until the clock stops flashing
and begins to count up (about 2 seconds).
You are now in the “Time Set” mode and can
operate either button to achieve the desired
setting. The buttons can be held down to scroll
through the digits, or pressed and released
lightly to advance one digit at a time.
When scrolling, the numbers will advance
slowly at first and then speed up to the rate
of about three per second. When the number
displayed approaches the desired setting,
release the button and press repeatedly to
advance one digit at a time. Be careful to
make sure that the PM indicator is on if a
PM time is desired.
Exiting “Time Set” Mode:
The “Time Set” mode can be exited in
one of two ways:
1. Press any button besides the “Hours” or
“Minutes” button. This will exit the “Time Set”
and activate the selected function.
2. Do nothing. If neither the “Hours” nor
“Minutes” button is pressed for a period
of five seconds, the “Time Set” mode will
be exited.

First, turn the Function Knob (bottom-left of the Control Panel) to “Clock”.

Hours: Press and hold the “HR” button to go through the numbers quickly. When the number displayed approaches the desired setting, release and press(pulse) the button to advance one digit at a time.

Note: When the number passes 12, the PM light will be displayed on the LCD.

Minutes: Press and hold the “MIN” button to go through the numbers quickly. When the number displayed approaches the desired setting, release and press (pulse) the button to advance one digit at a time.

To finish setting time, turn the Function to any setting other than "Clock", or simply wait until the numbers stop blinking.

try looking up the manual on the model number you might find it online. I have the maual for this model.

Here is how you adjust the time zone:
1.) push MODE till "AL" appears after the minute.
2.) tap "SET" (tap means push but do not hold) and time zone will advance.

3.) THE TRICK: The Time Zone can only be set in the Alarm Mode. Make sure you so not push and hold "SET" until the hour flashes as you would to set the alarm time. You just go into Alarm Mode and tap "SET" to advance the Time Zone by one zone per tap. When the Time Zone is where you want it, tap MODE to return to the clock and set the correct time.