Need a user manual for a conti aquabot cti-200 vacume cleaner

To replace the wheel tubes on an Aquabot Bravo III robotic pool cleaner, follow these steps:
1. Prepare the Pool Cleaner: Turn off the power to the pool cleaner and remove it from the water. Place it on a flat surface, such as a table or workbench, for easier access to the wheels.
2. Remove the Wheels: Locate the wheels that need the tube replacement. The Bravo III usually has four wheels, two on each side. Each wheel has a hubcap covering the axle. Use a flathead screwdriver or your fingers to pry off the hubcap from each wheel.
3. Remove the Wheel Tubes: After removing the hubcap, you will see the wheel tube inside. Carefully pull the wheel tube out of the wheel assembly. You may need to twist and wiggle it gently to loosen it. If the tube is damaged or worn, it should come out easily.
4. Insert the New Wheel Tubes: Take the replacement wheel tubes and insert them into the wheel assembly. Make sure they are properly aligned and seated securely.
5. Replace the Hubcaps: Once the new wheel tubes are in place, put the hubcaps back onto the wheels. Press them firmly until they snap into place, ensuring they cover the axle and wheel tube.
6. Repeat for other Wheels: If you need to replace the tubes on multiple wheels, repeat the process for each wheel that requires a replacement.
7. Test the Pool Cleaner: Once all the wheel tubes are replaced and the hubcaps are securely in place, place the Aquabot Bravo III back into the water and test its operation. Ensure that the wheels are turning smoothly and that the pool cleaner is functioning properly.
Note: It's recommended to refer to the specific user manual for your Aquabot Bravo III pool cleaner for detailed instructions and illustrations on how to replace the wheel tubes. The manual will provide you with any additional information or precautions specific to your model.

That is a load of rubbish. Tell us how to access the motor. There
Is no screws appart from the filter base

the foam filter for a Conti Aquarobot 1800w vacuum cleaner is unavailable. Can I use ordinary foam instead? Is the foam filter permanent or replaceable ?

I want to clean my vacum cleaner, How i can open my sanyo vacum cleaner model: sc-s260

Here is a page of articles from aquabot ,, lots of instructions you can view ..

http://www.123aquabot.com/Articles.htm

Please Vote !!

http://www.i-love-my-aquabot-automatic-pool-cleaner.com/Aquabot-Troubleshooting.html my give useful instrucyions, or, if you are near Phoenix Az I'll be glad to help! S. Christian [email protected]

I am not sure if this is the manual that you are looking for, or not, but just in case. If you following the link below it will take to you the T2 User's Guide, with the trouble shooting.

http://www.i-love-my-aquabot-automatic-pool-cleaner.com/support-files/aquabot-turbo-t2-manual.pdf

According to the trouble shooting guide:
Pumps Water, but Does Not Move or Moves Slowly
1. Remove any foreign matter that may be obstructing Drive Tracks.
2. Check Drive Belts and Tracks. Make sure they have not slipped out of place and that they're not loose.
3. Observe Drive Pulley, if it is not moving contact Customer Service.

check with the website: http://www.i-love-my-aquabot-automatic-pool-cleaner.com/Aquabot-Troubleshooting.html which gives a wealth of information and ideas to try. S. Christian [email protected]

The T2 has one set of belts and a single drive motor. Since one side must be rotating to be moving in a circle, we can then assume that the motor and belts are not the issue here. The two halves of the brushes are connected by a mechanism that allows them to turn independently of the other half. They can rotate about 3 times before they “lock” and act as it were one (not split) brush. This “slippage” is how the cleaner turns. Make sure that they do lock by manually rotating one side. If not, you will need new brush/wheel tubes.

A parts diagram can be found here:

Aquabot Parts and Repair