Set clock on ge profile gas range

The GE Profile, PGS950SEF3SS, has a convection oven. To set the time, press and hold both the 9 and 0 key pads for 3+ seconds. Then type in the current time with two digits for both the hour and minutes. (The range uses a 12-hour clock, in the US, but doesn't display AM or PM.) Press Start to save the time.

This information is in the manual on pages 12-13. Page 12 has a picture of the control panel. Page 13 has the procedure to set the clock as item 7. You can find the manual at GE on the product page: https://products.geappliances.com/appliance/gea-specs/PGS950SEFSS . The direct link to the manual is currently of https://products.geappliances.com/MarketingObjectRetrieval/Dispatcher?RequestType=PDF&Name=49-85213-4.pdf . SearsPartsDirect also has the manual here: https://www.searspartsdirect.com/partsdirect/user-manuals/pgs950sef3ss-ge-parts-manual . The direct link is https://c.searspartsdirect.com/mmh/pd_download/lis_pdf/OWNM/1512449L.pdf .

I hope this helps.

Cindy Wells

Here are the instructions for changing the clock from 12 to 24 hour and back.

12-Hour, 24-Hour or Clock Black-Out
Your control is set to use a 12-hour clock.
If you would prefer to have a 24-hour
military time clock or black out the clock
display, follow the steps below.

Press the BAKE and BROIL HI/LO
pads (on models, use
the upper oven controls) at the same
time for 3 seconds, until the display
shows SF.

Press the CLOCK pad once. The
display will show 12 hr. If this is
the choice you want, press the
START pad.

Press the CLOCK pad again to
change to the 24-hour military time
clock. The display will show 24 hr.
If this is the choice you want, press
the START pad.

Press the CLOCK pad again to black
out the clock display. The display
will show OFF. If this is the choice
you want, press the START pad.
NOTE: If the clock is in the black-out mode, you
will not be able to use the Delay Start function.

You didn't give a model number, but try the following:

For an electronic clock:
Touch the Clock pad. Touch the number pad. Touch the start pad until the time of day shows in the display. (Taken from the GE website)

F0
Stuck touch pad Usually means that either the touch pad or the oven control
(also called clock or ERC) is defective and needs to be replaced. If this fault
code cannot be cancelled, replace the oven control (also called clock or ERC),
touch pad, or both.

The F1 code can be 1 of 2 things. Try disconnecting the ribbon cable from the touch pad to the clock. Then reconnect power and if the code comes back with 32 seconds the eoc is bad. If it doesn't the touch pad is bad.

You might try to reset the unit by unplugging it. Plug it back in, reset the clock & try it again. Hope that helps.

i have found the code that you are looking for and hope that it helps you.
F1 Stuck touch pad Usually means that either the touch pad or the oven control (also called clock or ERC) is defective and needs to be replaced. If this fault code cannot be cancelled, replace the oven control (also called clock or ERC), touch pad, or both.Thank you for writing to fix ya.

Best Regards Richard

This is your electronic control board that needs to be repalced on this unit. GE Profile is a great brand and it is easy to repair, also.

We provide part removal/installation instructions for our customers when you purchase your parts from us.We also ship parts overnight to assure that you get your oven repaired right away.

Please contact us at:
http://www.fixya.com/repair/d499389-accurate_appliance_repair_service
from 7 AM until 9 PM CST. We look forward to getting you cooking again soon.

Thanks, Ella

On a GE range oven F7 indicates either a function pad button is stuck or the clock on the oven is malfunctioning . F7 A = Function pad button stuck or
B = Bad clock Unstick button or
Replace Electronic Range Control (ERC)
It looks like you have a function button pad stuck or a bad clock.

Unstick button or replace electronic range control. you can get the required parts at www.repairclinic.com thanks.

Anyone has any information as to how to fix my describe problem with GE Profile Gas Range I have.

Thanks