Question about Skagen 355LSSM Wrist Watch
HOW DO I CHANGE THE DAY AND DATE FOR THIS WATCH? THANKS
The Skagen watches have two-step stem; fully pulled out will change the time and partially pulled out will change the date (only goes one way so try turning it counter-clockwise or clockwise - I forget which is correct). It's easier to find the date length by extending it all the way and then go back toward the case. It won't change the date if you run it through a 24-hour cycle - you have to do the half-way thing. Hope this helps.
Posted on Nov 24, 2008
I have an old analog quartz Timex watch with a mechanical day and date display. The stem pulls out to only one position which moves the hands. As the hands are rotated past the midnight (not noon) position the date changes first and then the day.
The simplest way I found to adjust both the day and date is to advance the hands forward through the midnight positions until you reach the desired day. As soon as the day clicks into the desired position back up the hands through the midnight position to about the 10 pm position. This resets the mechanism to set the day/date. Then advance the hands towards the midnight position carefully until the date changes and before the day changes. Again back up the hands through midnight until about 10 pm and then forward to advance the date, stopping before the day changes. Repeat the last two steps until you get the correct date. Then rotate the hands back to the correct time, if it's a morning time be sure to rotate all the way back through 12 noon to the correct time. Hope this helps.
Posted on Aug 26, 2008
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
Here's a link to this great service
Posted on Jan 02, 2017
There isn;t any downloadable manuals for Rolex watches, but operation of Rolex Day-Date is very simple:
1) when you unscrew the crown, it is in winding position,
2) when you pull out the crown to the first click, it is in day and date setting position (depending wich way you turn the crown).
NOTE: to adjust the day or date, previously you have to advance hands forward, passing 12 o'clock (midnight) mark and stop advancing at 4.00 a.m. using the crown in position as described in chapter 3. When done - push the crown fully in, then pull out to the first click and only then adjust the day or date.
3) when you pull the crown further out to the second click, it is in time setting position.
To find the daytime or night time on the watch: pull out crown to the second click and advance watch hands forward till you pass the 12 mark on dial. If the date changes as you pass it - it is the night time (midnight). If the date do not change as you pass it - it is the daytime (noon).
After all settings being done, allways screw the crown back down as it protects the watch from water and moisture.
Never use watch in sauna- it's not designed for that.
Do not forget to rate, please.
Posted on Mar 07, 2009
Alhamdulillah, the problem solved (at last) tks to IRONMAN
The steps are like this :
1. Pull the crown full, and turn it clockwise until you find the right day.
2. and then push it one click (dont push it to hard so it back to normal position) and turn the crown counter clockwise to adjust date.
3. Push the small button near the crown to adjust month.
and voila... the problem solved
Posted on Jul 05, 2009
I just dug my watch out after not wearing for a few years and had the same problem. There is an easy way to adust this watch's time and alarm, basically one way to enter both.
1) With the watch in the regular time display mode (doesn't matter if 12 hour or military time), depress and hold the lower left hand button (mode button). After a few seconds the watch appears to shift to alarm mode and it is blinking. This puts you into the mode for adjusting the alarm.
2) If you want to adjust time, date, etc rather than alarm time, after you have done step one, simply press that same lower left button again, and then it will put you into the time mode, but this time the time mode is blinking and you can adjust the various components (seconds, minutes, hours). You can only move minutes, hours, etc forward, no way to move backward. You will start off with the second display blinking, probably skip that unless you need to adjust seconds. Depress the upper right button to shift to the next option (minutes) and you will see the minute display blinking. Adjust the minutes by depressing the lower right button. When finished depress upper right button to move to next option (hours) depress the lower right button to move the minutes/hours/month/date forward as necessary, when you finish just press the lower left button again and it pulls you out of adjust mode and you are back in regular time viewing.
I had to post this because I've had this problem in the past and it killed me. Its kind of intuititve after you get into the adjusting mode by pressing the lower left button- remember, initially it will put you into adjust alarm mode, but press again and you will get into adjust time mode.
Posted on Nov 12, 2008
Tips for a great answer:
Sep 19, 2011 | Timex T2E581 Watch for Men
Jun 07, 2011 | Hamilton X-Wind H77646733 Wrist Watch
Aug 03, 2010 | Watches
Jun 16, 2010 | Sector 550 Series Chronograph R3253993035...
May 13, 2010 | Invicta 2302 Wrist Watch
Oct 17, 2008 | Watches
Sep 07, 2008 | Watches
Dec 03, 2007 | Watches
Oct 15, 2007 | Timex Men's Black Reef Gear i-Control...
5,421 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: