Where can I get a replacement ribbon (printed circuit) connecting the arial to the main body?

You have identified a problem with the IR sensor on your JVC LT-58MAW595 television. The IR sensor is responsible for receiving signals from the remote control, so if it is damaged or not functioning correctly, the tv may not respond to remote commands.
If the IR sensor is caved in and has scraped the gold ribbon cable that is in line with the sensor box, the ribbon cable has also likely been damaged. The ribbon cable is a thin, flexible circuit board that connects the IR sensor to the main circuit board of the television.
In this case, you may need to replace the ribbon cable to repair the IR sensor. The ribbon cable is a small part, and it is not a common one; it is part of the main circuit board of the television.
It is not recommended to try to repair the ribbon cable; it is best to replace it with a new one.
The part you are looking for might be hard to find, and it might be best to contact JVC or a professional technician to determine the availability of the ribbon cable and the replacement cost.
Keep in mind that working with the main circuit board of the television requires technical knowledge and skill; it's best to have a professional technician perform the repair.

there are three usual faults that cause this
1. the scanner is unable to locate home position- remove the scan glass/ clean and lubricate all rails
2. the ribbon cable has open circuit on tracks- replace the ribbon cable connecting the scanner to printer
3. the printer main PCA has failed and cannot control the scanner- replace main PCA

Error 49 relates to the print head drive voltage. It may just need the flat ribbon cables that connect the head to the main pcb reseating, but equally it may need the print head replacing (most likely).
An outside chance that the main pcb will need replacing.
In theory, all of these jobs are a task for an engineer.

the problem may be a combination of three things, it may be the lcd panel, the main printed circuit board, or the logic printed circuit board, the small circuit board that the panel plugs into sometimes. replace either one at a time or all, these situations always come with some trial and repeat testing. Good luck.

Try this:


1- Turn off power and unplug from power source.
2- Open right side of printer (looking at the front).
3- Disconnect,by pulling gently, both white flat ribbon cables off the main circuit board.
4- Plug in power source and turn printer on. Wait till you get a error message and push "OK".
5- Unplug power source.
6- Reconnect the flat ribbon cables by aligning and carefully pushing into the conectors on the main circuit board.
7- Plug in power source and turn printer on (Printer preparing occurred).

OKSolution 1:

1. Turn off power and unplug from power source.
2. Open right side of printer.
3. Disconnect,by pulling gently, both white flat ribbon cables off the main circuit board.
4. Plug in power source and turn printer on. Wait till you get a error message and push "Ok".
5. Unplug power source.
6. Reconnect the flat ribbon cables by aligning and carefully pushing into the conectors on the main circuit board.
7. Plug in power source and turn printer on.

Solution 2:

1. Turn off power and unplug from power source.
2. Open right side of printer (looking at the front).
3. Disconect,by pulling gently, the flat ribbon cable off the main circuit board that is the smaller of the two.
4. Plug in power source and turn printer on. Wait till you hear no more movement from inside from unit booting up.
5. Press both cancel and power button at the same time.
6. Message on printer screen will be, "Enter Special Key Combo".
7. Push keys; Left-Ok-Right.
8. When printer screen changes, scan through and look for "System Menu" and push "Ok"
9. Scan agan and look for "Clean Derivative" and push "Ok". Wait for 1 minute.
10. Scan agan and look for "Clean Firms" and push "Ok". Wait for 1 minute.
11. Press "Cancel" 4 times
12. Turn off power and unplug from power source. Wait for 2 minutes.
13. Reconect the flat ribbon cable by aligning and carefully pushing into the conector on the main circuit board.
14. Plug in power source,and turn on power.
15. When printer boots up, answer the questions on the printer screen for your area.
16. The printer will cycle the ink from the cartridges to the print head and back.

Pineworks

Error 49 relates to the print head drive voltage. It may just need the flat ribbon cables that connect the head to the main pcb reseating, but equally it may need the print head replacing (most likely).
An outside chance that the main pcb will need replacing.

In theory, all of these jobs are a task for an engineer. Brother UK (0870 830 400) can pass you on to a repair agent.

Yes

If the Freeview box is not connected to the main aerial socket, you cannot get a signal.

Also, you will need a digital aerial, if you don't already have one.

You have replaced the item which is commonly the cause- the printhead. The other possible problems are: a connection break in the printhead ribbon cable, which makes electrical connection from the driver circuitry to the printhead. Look for a tiny crack, especially along the edge of this ribbon cable. Another possibility is an electronic component defect in the circuitry which fires the printhead, or maybe a loose solder connection in the same circuit. Lastly, when you replaced the printhead, are you reasonably certain the replacement head didn't have a broken top pin or two?