Trying to track a new phone in route - Cell Phones

How is your carrier ?
Sprint has a family locator app, that can be set up without any notifications.

From the saved data when you backed it up on the computer. Use Garmin Express to transfer.

How to Backup User Data from GPS 72/76 or GPSMAP 76/76S

https://support.garmin.com > en-CA
It is recommended to occasionally back up the user data on your GPS 72/76 or GPSMAP 76/76S. User data includes waypoints, routes, tracks, and geocaches.

• 
  

  Transfer User Data From MapSource to a GPS 72/72H/76 or ...

  https://support.garmin.com > en-CA
  To transfer user data, such as waypoints, routes, and tracks from the MapSource program to these devices, some additional equipment will be required.
• 
  

  Manually Creating Waypoints on GPS 72/76 or GPSMAP 60 ...

  https://support.garmin.com > en-CA
  Press and hold Enter · Wait for the New Waypoint screen · Release Enter · Highlight the Coordinates field · Press Enter · Adjust the coordinates as desired with the ...
• 
  

  Backing Up Userdata (Waypoints, Routes, and Tracks) From a ...

  https://support.garmin.com > en-CA
  Before updating device software, it is recommended that you back up user data like waypoints, routes, and tracks. This should be done at regular intervals ...

Buzzing is usally AC line noise leaking into an un-shielded cable somewhere or a floating ground. If the AC plug is reversible, try that. Sometimes the buzz is from an attached device. Make sure all audio cables are plugged in tightly at each end and routed away from or at right angles to any power cords and away from other sources of strong magnetic fields like TV's.

Disconnect the input(s) and see if it hums in the absence of an audio source. A bad audio cable shield or unwisely-routed audio cables will allow entrance of unwanted signals from external power sources, magnetic fields, even dimmer-controlled track lights.
I've also seen variable track lights induce noise but it's usually minor.

Try rotating the power cord in the wall outlet.

If it still buzzes with no cables or anything external attached there's an internal problem.

First you need to add group track . .

Goto Project > AddTrack > GroupChannel (mono / stereo)

The new group will be visible in Mixer Window . .Do necessary routing . . & you are ready to rock . .

We had this problem numerous time (luckily while under an extended warranty) our local dealer tried fixing it many times, they even put a heavier motor under the seat. After one repair the seat motor stopped working within 2 miles. My husband turned around stayed out in the shop and helped the mechanic discover that when the seat went back at a certain point, the wire under the drivers seat was routed so that it traveled into the seat track and back out, when it went into the track it got pinched and shorted out. (you CAN NOT tell if this has happened by looking under the seat, the wire will NOT still be trapped in the seat track or severed, at a certain point the wires traveled into and then back out of the track causing a main wire to short out (wires are harnessed under the drivers seat which control movement in both seats). The solution - a new wire harness was installed and the wires had to be routed differently to prevent this from happening. The repair only took a few minutes the wire harness had to move over about three inches and the wires got ties to hold them out of the way. That was three years ago and so far this has not been a problem again. Hope this helps, or gives you some place to start looking.

Sounds like you have a custom app. I would suggest to contact sofware developer. You can always contact me by phone or email 630-622-2024 [email protected] Please visit our website www.legacyglobal.com

you do this through the computer with software u DL from manufacturer website and download to gps

This may sound really stupid on my part, but if the auxillary out requires phantom power did the phantom power switch get changed possibly?

Lot of possibilities.

The DP-01 is like a mixer with built-in recording capabilies. You could plug your tunrntables into your DP-01 inputs, assign the inputs to tracks(channels) on the DP-01, and then output those tracks to two channels on your mixer (which would be connected to your PA.

Alternatively, you could plug the outs from your mixer into the DP-01 either by routing individual channels from the mixer into the DP-01 inputs, or outputting the mix into a single track (or into two tracks in stereo on your DP-01). Just assign the DP-01 inputs as usual to the tracks you want to record onto.

Those are just a couple of basic ideas. You could also route a DP-01 track (or the whole mix) back out the DP-01 send loop and through some external processors and then back to tracks on your DP-01, or you could do this through the mixer and then record the final result on the DP-01.

Under settings, Navigation, verify that Vehicle is set to Car/Motorcycle.