After hands-free red light for sealing turns on, why does it take a long time to start sealing?

Check the belt and the end bearings are free by hand. (electric off plug out) if not free remove plate to access roller/brush, remove clear any obstruction (Hair/string/thread) replace and test. ensure you site belt back on to spindle and roller/brush correctly...

First you have to make a bag, so pull from the roll to the size you need, you might want to practice with a small one the first time.
Press the lid gently and the heat light should come on, when it turns green open the lid and you will have sealed one edge of the bag. (usually red means it is heating and green means it is finished)
To seal, place the bag over the vacuum nozzle to remove the air, usually pressing one corner starts the vacuum. When as much air is gone as you want, gently press the center of the lid again, and when the light is no longer red your bag should have the air gone and the bag sealed. DO NOT press too strongly on the center as that will cause the heated wire to cut the bag.

Hello,
A fairly common occurence with Miele dishwashers is the seal on the pump/motor assambly swells up freezeing the motor.Miele makes tool to free it up very easily,if it doesnt reoccur the seal just swelled and it will be ok once freed up.If it does reoccur the seal needs to be replaced. Any Miele authorized service company will have this tool and could free the motor up within 5 minutes and only a couple uses will tell if it will swell again and need to be replaced.

Perhaps Miele could send you one of those tools so you could try and see it the pump seal has swelled up and stuck.



Gene

Hello,
Count how many times the red light flashes and how many the green light flashes.If its 1 green and 1 red thats water problems.If 2 flashes of red light check filter is clear and pump is free to turn.

Hope this helped.

try a total defrost,to clear any internal ice(every 12 months)then switch on and if you have a rapid freeze button leave on for 24 hours to get back to normal operating temp.if you have hard ice around the door seals then you have an air leak which you must sort out(try using a hot cloth to warm seals back into shape.....seals should fit all round, all the time.

how old is the xbox and does it still have a seal behind the faceplate? if its under 3 years and still sealed phone microsoft they will repair for free

just bought mine - how long does it take to heat up? it's been 10 minutes already, I don't feel any heat. no lights coming on, but when I pushed on the lid, the vacuum started, so I know it's "on"

Turn it off, then when you turn it back on keep the power button (the green one) down until the blue light starts flashing red and blue.

The lights are working, the batteries aren't. Red indicates power to the charger, and it should be on all the time. Green indicates a full charge, usually. If one or both of the batteries are totally dead, then the charger can't "see" them, and you will get a green light, but you will have dead batteries.

All power chairs use sealed, deep-cycle batteries. Deep cycle batteries, are designed for slow amperage dischare over a long time period, unlike a car battery that throws out a lot of amperage for turning the motor over. That's called "cold-cranking amps", and you can load-test a car battery to see if it will throw out a ton of amps for long enough to start a car. There is NO load tester made, or possible for a deep-cycle battery. A load test requires a 24-hour time period, and a complicated formula.

So, your course is to get some fresh, gel-sealed-batteries. You will need type U-1. Specify, gel-sealed-batteries when you go to the battery shop. A fresh set should get the chair up to about 12-16 mile range, which would be about 3-4 hours running constantly at high speed. Good luck.

sounds like the engine management fault code signal. there is a free download service manual here. with it you should be able to decifer it http://www.carlsalter.com/motorcycle-manuals.asp