Question about Sceptre E465BV-FHDD 46" 3D LED TV 1920x1080, 60 HZ, HDTV, 3D

2 Answers

LED TV Wont Turn on, just shows red indicator light

The TV has had problems turning on... When plugged in, indicator light shows red. when pressing the power button, tv doesn't come on. Would have to unplug from power, wait a few minutes, and re-plug tv back in and try power button.. Normally this would work and indicator would turn blue. If tv doesn't show Sceptre Logo screen after 5 seconds, tv doesn't turn on. if it does great. Now tv isn't turning on 95% of the time. and if indicator does show blue, 10% chance tv turns on. any suggestions?

Posted by on

Ad

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.

  • Contributor
  • 1 Answer

What if you have the Same issue but replacing the Power Board did not fix the issue? It just shows the red light. Once the Power button is hit then the red light disappears and never comes back untill you replug into an outlet, and the TV still wont come on?

Posted on Dec 11, 2015

Ad

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    New Friend:

    An expert that has 1 follower.

    Cheetah:

    An expert who has answered 20 or more questions within one hour.

  • Expert
  • 78 Answers

Dead power board

Posted on Dec 11, 2015

Ad

1 Suggested Answer

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Westinghouse ew32s5kw tv red light shows power is going to unit pressing power turns indicator light from red to blue for a brief moment then back to red.


I had the same problem on my Westinghouse 32 inch TV. The internal main power supply went bad and had to be replaced. I had a TV repair shop do it. It was about 8 years ago. Haven't had a problem since. I think it cost about $70 for parts and labor. Nowadays TVs are pretty much a throw away item if they go bad. TV repair shops are getting hard to find plus the cost of TVs has come down so much sometimes you can get a new set for what the repair would cost!

Oct 25, 2017 | Westinghouse Televison & Video

1 Answer

X322BV-HD*WXC100


Warranty is usually 1 year parts and labor. Contact mfc for warranty service. likely main board.

May 28, 2013 | Televison & Video

1 Answer

Hi, i have a sony bravia klv-40x350a, last week, we suspected a lizard died inside our tv because of the smell was very strong near the on and off botton. we plugged the tv, the 1st pressed in the remote...


Hello.You need to open the back cover to see where is the location of the burned and died lizard.First you do is to clean the area of lizard died and try to power on again.

Jul 01, 2011 | Sony Televison & Video

1 Answer

WHAT IS CODE FOR TV SANYO?


Hello

If you wants to get into the service mode of Sanyo TV. do one moung the folloing procedure. If you are in need of universal remote code for Sanyo follow the extented solution. Your post is not clear, that is why I answers for both.

To get in to the service mode adjustments

[1]

Unplug the power cable.
* Press and hold the {MUTE} button on the remote control while plugging the power cable back into the outlet.
* Keep pressing the {MUTE} button until the TV powers on with the Service Menu displayed.
* Use the {CH+} {CH-} buttons to select menus.
* Use the {VOL+} {VOL -} buttons to change settings.
* Some menus might have sub-addresses. Use the numeric buttons {0} to {7} to adjust sub-item data.
* Press the {MENU} button or turn the TV off to exit.

[OR]

Unplug the power cable.
* Press and hold the {VOL -} button on the TV
while plugging the power cable back into the outlet.

* Keep pressing the {VOL -} button until
the TV powers on with the Service Menu displayed.

* Use the {CH+} {CH-} buttons to select menus.
* Use the {VOL+} {VOL -} buttons to change settings.

* Some menus might have sub-addresses. Use the
numeric buttons {0} to {7} to adjust sub-item data.

* Press the {MENU} button or turn the TV off to exit.

Universal remote codes:

Three digit universal remote code for sanyo are:
004/ 013/ 049/ 108/ 110/ 180/ 209

Four digit universal remote code for Sanyo are:
0049 0097 0110 0004 0268 0012 0108 0180

Direct Code Entry
  1. Press and hold the SETUP button until the red indicator stays on, then release the SETUP button.
  2. Press and release the desired Mode button (TV, VCR, etc.). The red indicator blinks, then stays lit.
  3. Enter the 4 digit code from the code tables. Note: after a valid code entry, the red indicator turns off. For an invalid code, the red indicator flashes.
  4. With your device on, press CHANNEL UP. If the device responds, no further programming is required. Note: If some buttons do not operate your device, try one of the other codes for your brand.
OK.

Jan 25, 2011 | Televison & Video

1 Answer

I have a 32 Akai HD TV I found the following problem when I returned from vacation The red light is showing. I press the power button, the green light comes on for a short while and then goes back to red....


Symptoms of a Defective or dying Power supplies on LCD TVs. 1. Light(s) on the front panel are behaving not normal example, blinking, amber color or not steady, fainting, etc. 2. TV not turning ON properly. 3. TV turns OFF by itself. 4. Needs to be unplug to many times to make it work. 5. Humming or high pitch noise heard through speakers or at the back of the TV. I repair these power supplies. Write to jah2mil@hotmail.com if you require further assistance.

Jun 12, 2009 | Akai LCT3201TD 32 in. LCD Television

2 Answers

TV Won'T Turn On


A fuse is not your problem. this TV has a safty feture that when it senses a problem it cuts the power to prevent any fouther damage, when you un plug it the TV resets and it will turn on agian. I have the same TV Check the CRT light guns there are 3 of them. If one goes bad it will cause your problem.

Sep 22, 2007 | Panasonic PT-51HX41 51" Rear Projection...

2 Answers

New Sceptre 37" LCD TV does not turn on


I just got a 42" komodo by Sceptre, same problem, except "SCEPTRE" showed on the screen. I was sent a USB key program to insert in the service slot in the back and it reflashes the bios. This is old news for you but maybe new for someone?

Aug 28, 2006 | Sceptre X37sv-Naga 37 in. LCD Television

Not finding what you are looking for?
Sceptre E465BV-FHDD 46" 3D LED TV 1920x1080, 60 HZ, HDTV, 3D Logo

1,027 people viewed this question

Ask a Question

Usually answered in minutes!

Top Sceptre Televison & Video Experts

The Knight
The Knight

Level 3 Expert

76177 Answers

leeboy3909

Level 1 Expert

9 Answers

Ekse

Level 3 Expert

13434 Answers

Are you a Sceptre Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...