How do I connect to wireless and Ethernet?

So what is the connection ? USB or Wireless or Ethernet ?
Did you try connecting though other ports ? Connectivity, standard

• 1 Hi-Speed USB 2.0
• 1 Host USB
• 1 Ethernet
• 1 Wireless 802.11b/g/n

see wireless setup shown in the below video at 24.34 minute mark
HP Officejet Pro 8610 Unboxing Setup

Check the date/time on the XP box. This is not uncommon.

so the pc is recognizing the hardware? go to support.dell.com, and type in your service tag and download the latest drivers for your hardware? if that doesn't help, press the windowsk and the R key and then type cmd and press enter. type 'ipconfig' no ' and press enter
post those results here. if you're connected to the internet but are unable to load web pages it's possible your browser is set up to use a proxy. open up IE or FF or chrome and go to the connections tab and make sure that the box that says 'use proxy for this connection' is unchecked.

If you need further help, reach me via phone at https://www.6ya.com/expert/joel_63c670a84e9f6a97

Here are some guidelines to identify and fix your wireless communication issue:

• What is the status of the Wi-Fi light on the printer? Green light means that it's connected to a wireless network while Orange light means it's not connected to a network.
• Try to print the printer's wireless network settings to determine if it's connected to your own wireless network. On the printer operator panel, touch the Setup button > Network Setup > Print Setup Page. Your printer will then print the its wireless network information page. Ensure that the printer is connected to your network by checking the Network Card Status, Wireless SSID, Quality or Trouble Code.
• If printer is not connected to your network, you may need to reset your printer's wireless network settings. On the printer operator panel, press Setup button > Network Setup > Reset Network Settings. The Wi-Fi light on the printer will momentarily turn off then back on to solid orange. You can then run the Wireless Setup Utility application on your computer to reconfigure the printer to connect to your wireless network. On your computer, launch the Lexmark Printer Home application > go to Settings tab > Wireless Setup Utility. Please follow the instructions on your computer screen.

If you still need assistance, please contact Lexmark Technical Support Center for additional assistance.

The Linksys Wireless router is fine, but your latop is not configured for DHCP (Dynamic Host Configuration Protocol). The computer is connected to the router at layer 2, whereas HTTP (Hypertext Transfer Protocol), sits
atop the TCP/IP (Transmission Control Protocol/Internet Protocol) layer, and seems to be trying to
query the ISP's (Internet Service Provider) network for a nameserver (via DNS (Dynamic Name Service) protocol) that doesn't exist on the ISP's network. Configuring the laptop for DHCP and specifying no nameserver will fix this (the ISP's network will dynamically assign a DNS).

Its also possible (though a remote possibility) that your Linksys wifi router may be configured to disallow TCP/IP virtual circuits to/from your computer's IP address - but this is a really advanced
capability of your Linksys wifi router - few know this capability even exists.

Connecting multiple wifi devices to the Linksys router should be no problem, just configure them all to interact with the router using DHCP.

According to Nintendo, error 32002 means: "Lost connection during Wii system update". So, the problem probably lies either in your internet connection or in Nintendo's server. If you're using a slow internet connection such as dial-up, then the easiest solution would be to upgrade to a faster connection - most modern gaming applications require one anyways. However, if you're using a faster internet connection, try these tips:
- If you have a wireless connection, be sure that no one is using a microwave or cordless phone while you are trying to download the update, both of these devices can cause interference
- If you are on a college campus or using a shared internet connection with many people, try updating your console at an unusual time, like two or three o'clock in the morning when no one else is online
- wait a day or two and try again; Nintendo may be having server troubles
- call Nintendo's helpline at 1-800-255-3700 and tell them about your problem
Hope this helps!

You can try to check if you have done the steps here. If everything fails, you might consider getting a USB cable to connect the printer directly to the computer first and use the Kodak Printer Setup Utility to connect. Make sure to install the printer's driver and software using the disc beforehand.

Is there any computer connected to the router ?
If not then you will need to connect the computer
to the router.
Do not change any wireless settings on the router
with the wireless computer.
you will need to connect the computer to the
router with the Ethernet cable.
check the IP address of the computer.
open the router set up page of the router.
Here you can change the wireless settings of the
router.
Now once you change the network anme and security
on the router, you will need to connect to the
wireless network on your wireless computers.
Click Here for step by step instructions

Try to do port forwarding. Search for the port number that the game uses and open it on the router's Setup Page using Port Forwarding.

I would guess you didn't do it in the correct order.

Are you 100% positive th  Ethernet cables are in the right ports?

Check the one that goes from the modem, to the router.

If that doesn't help, would you let me remotely control your PC and see what it looks like?