Panel is flashing

it flashes if the program is in pause mode
press the start button again to get the program to start

CODES: The Express program light Keeps flashing quickly

MEANINGS: Longer inlet time

Possible Cause: Faucets is not opened, or water intake is restricted, or water pressure is to low.

Hi,
Please try these steps:
1. Try to uninstall flash player by use Add/ Remove programs.(Start - Control Panel- Add/Remove Program)
2. Go to Adobe website download latest version of Flash Player and installer it. Adobe Website will verify the installation for you. Go here for the Flash Player
http://www.adobe.com/support/flashplayer/downloads.html

This can be done under administrator account only. If new message say you can't uninstall because program is in use, please open Task Manager and End Flash Player task then keep doing the uninstallation.
Hope this will help.
Thanks for reading.

If this is a Whirlpool manufactured dishwasher, the blinking clean light is an interruption in the dishwasher program that usually indicates a component problem or program malfunction. If a component is defective, it is commonly attributed to the heating cycle or thermostat problem. To rule out component failure, or program error, the following link explains how you may be able to clear the blinking clean light problem and possibly avoid a service call:

http://www.fixya.com/support/r3575752-dishwasher_blinking_clean_light

Keep in mind all dishwashers are not alike and have different panel options. If you do not have the same set up that I have mentioned, the tech sheet for your dishwasher will explain the touch pad functions. The tech sheet is located behind the lower toe panel under the door and lists the proper sequence of buttons to push for diagnostics and troubleshooting. Just remove the screws that hold the panel in place and remove.

NOTE: Sometimes the tech sheet is located behind the inner door panel. You will need to remove the screws securing the inner panel to access it if this is the case. Make sure you turn off the main power breaker before doing so.

In many cases, I found this to be a momentary glitch in operation. If the problem keeps reoccuring the number of flashes is an indication of WHICH circuit is causing your problem. As all dishwashers differ in operation and features, refer to your tech sheet for the recommended troubleshooting steps.

NOTE: Some dishwashers use the Sani-Rinse/Air Dry combination, some use the Sani-Rinse/Heated Dry combination. Some use a sequence of three, others use a sequence of 5 pushes of the buttons. If the tech sheet is not located behind the lower toe panel, it should be affixed somewhere under the dishwasher. I have also found them located inside the inner door panel.


If you still need assistance, please post back with your MODEL NUMBER and let me know

If this is a Whirlpool manufactured dishwasher, the blinking clean light is an interruption in the dishwasher program that usually indicates a component problem or program malfunction. If a component is defective, it's often attributed to the heating cycle or thermostat failure. To rule out component failure, or program error, the following link explains how you may be able to clear the blinking clean light problem and possibly avoid a service call:

http://www.fixya.com/support/r3575752-dishwasher_blinking_clean_light

Keep in mind all dishwashers are not alike and have different panel options. If you do not have the same set up that I have mentioned, the tech sheet for your dishwasher will explain the touch pad functions. The tech sheet is located behind the lower toe panel under the door and lists the proper sequence of buttons to push for diagnostics and troubleshooting. Just remove the screws that hold the panel in place and remove.

NOTE: Sometimes the tech sheet is located behind the inner door panel. You will need to remove the screws securing the inner panel to access it if this is the case. Make sure you turn off the main power breaker before doing so.

In many cases, I found this to be a momentary glitch in operation. If the problem keeps reoccuring the number of flashes is an indication of WHICH circuit is causing your problem. As all dishwashers differ in operation and features, refer to your tech sheet for the recommended troubleshooting steps.

NOTE: Some dishwashers use the Sani-Rinse/Air Dry combination, some use the Sani-Rinse/Heated Dry combination. Some use a sequence of three, others use a sequence of 5 pushes of the buttons. If the tech sheet is not located behind the lower toe panel, it should be affixed somewhere under the dishwasher. I have also found them located inside the inner door panel. Please post back with your MODEL NUMBER if you still need assistance.

Adobe flash player and google toolbar are 2 different things. I don't think you want to get rid of adobe flash player because it is needed to correctly display many web pages but you can get rid of google toolbar.

To do that, go to start, control panel, and under programs, click uninstall programs. Scroll down until you see google toolbar. Click on google toolbar to highlight it. On the top of the window, click uninstall. Follow the wizard until it says the program was successfully uninstalled. You may need to restart your computer once the program is uninstalled.

Let me know if this solves your problem.

flash player issue are very complicated but you can first start with Uninstalling the flash player from the Add/Remove Programs and then reinstalling it.
Start->Control Panel->Add/Remove Programs (Programs and Features)

Then go to the Adobe.com and download the latest version of Flash Player.

If you are still not able to use your flash player then it might be some virus issue or could be some issue with the registry of the computer.

Hi,

Click on Start Button
Click on Control panel
Open Programs and Features
Click on View Installed Updates ( from left panel )
From the list check for the update done by date ( since when the issues started )
Click on the update and click Uninstall from top bar.

Restart your PC and it should work fine.

Regards,
Shawn.

Close all web-browser windows (Internet Explorer and Firefox).

Click Start
Click Control Panel
Click Classic View
Click Add/Remove Programs
Click to select Adobe Flash Player.
Click to uninstall.
Close Add/Remove Programs.
Close Control Panel.
Access: http://www.adobe.com/software/flash/about
and allow it to install the most-current version of Flash Player.
Try again to watch a video.

The blinking clean light is an interruption in the dishwasher program that usually indicates a component malfunction. This can also be a result of a momentary program glitch. If a component is defective, it's usually attributed to the heating cycle or thermostat failure. To rule out component failure, or program error, the following link explains how you may be able to clear the blinking clean light problem and possibly avoid a service call:

http://www.fixya.com/support/r3575752-dishwasher_blinking_clean_light

Keep in mind all dishwashers are not alike and have different panel options. If you do not have the same set up that I have mentioned, the tech sheet for your dishwasher will explain the touch pad functions. The tech sheet is located behind the lower toe panel under the door and lists the proper sequence of buttons to push for diagnostics and troubleshooting. Just remove the screws that hold the panel in place and remove.

NOTE: Sometimes the tech sheet is located behind the inner door panel. You will need to remove the screws securing the inner panel to access it if this is the case. Make sure you turn off the main power breaker before doing so.

In many cases, I found this to be a momentary glitch in operation. If the problem keeps reoccuring the number of flashes is an indication of WHICH circuit is causing your problem. As all dishwashers differ in operation and features, refer to your tech sheet for the recommended troubleshooting steps.

NOTE: Some dishwashers use the Sani-Rinse/Air Dry combination, some use the Sani-Rinse/Heated Dry combination. Some use a sequence of three, others use a sequence of 5 pushes of the buttons. If the tech sheet is not located behind the lower toe panel, it should be affixed somewhere under the dishwasher. I have also found them located inside the inner door panel. Let me know if you still need assistance.