How to set up date & time? Did it once but manual/Users Guide can't locate.

To set the date and time on your camera, follow these steps:

Turn on the camera and set the language and date/time by following the instructions in the Extended User Manual.
Once you have set the date and time, you can turn on the Date Stamp feature by following the instructions in the User Manual . The date and time will be stamped on all pictures taken with this feature enabled.
KODAK CD82 - EXTENDED GUIDE EXTENDED USER MANUAL Pdf Download ' ManualsLib

KODAK EASYSHARE CD82 USER MANUAL Pdf Download ' ManualsLib

Try setting the clock on the remote press [FUNCTIONS] go to SETUP menu - locate the CLOCK option (it should be under 'OTHERS' in the setup) and set the current time, press [ENTER/OK] to store if necessary, then press [RETURN] to exit the setup. Once clock is set correctly, future DVD thumbnails will show the actual date/time of recording in this (and similar) model combo units. If auto clock setting is not possible, set it manually as above.

I assume in spite of the wrong date/time, your DVD recordings have been successful. Incorrect clock and date setting usually only affects timer recording for VHS.

If you have lost or misplaced your original owner's manual, you can download a free pdf version (for Region 1 model) from:

http://www2.panasonic.com/consumer-electronics/support/Video/DVD-Recorders-Players/DVD-Recorders/model.DMR-EZ48VK

or, if you live outside USA, download the 'Australia/NZ' pdf version of the manual (for Region 4 model) from:

http://www.panasonic.com.au/Products/DVD+and+Blu-ray/DVD+-+Players+and+Recorders/DMR-EZ48V/Downloads

either one of these will provide you a full copy of the original user guide/setup including clock.

All free. Hope these suggestions help.

According to the Kodak website the Z981 can be set up for date stamp. I could not locate a users guide, but it mentions it under Custom settings.

Turn on the GPS. The forerunner will automatically sync time and date. Make sure the DST is switched to auto. I had the same problem and researched for the answer....which led me here. Turning on my GPS sync'd time and date for me. I hope this helps

The attached URL worked for me:
http://www.ccrane.com/instruction-manuals/e-howard-and-co-atomic-watch-eh23sa.pdf

Page 1-16 of the NetworkAdmin Users guide.

In the network settings, select "No" for use NTP to enter manuall.

Log in as administrator though Pagescope Webconnect and set the time manually there easier.

Please find the information requested at the Users Guide of Motorola V170 at the manufacturer's site. (Simply left click the link below) When the page opens you will see the link to the User's Manual at the left of the webpage (1.6Mb Download - Pdf File)

http://www.motorola.com/consumer/v/index.jsp?show=productHome&vgnextoid=e015ab651780b010VgnVCM1000008206b00aRCRD

If for any reason you cannot access the motorola site simply do the following at your phone.

Setting Up Your Phone - Setting the Time and Date

Start at the start screen of the phone
Find the Feature M> Settings >Other Settings > Initial Setup >Time and Date


Regards

Please don’t forget to rate this solution if it was helpful, it keeps us going!

There are manuals here with a link to adobe reader so you can view them.

http://h10025.www1.hp.com/ewfrf/wc/manualCategory?lc=en&cc=us&dlc=en&product=3366990&lang=en&

Page 37 of the users guide addresses printing dates

cannot find a reference to confirmation

You will need Adobe Reader to open the manuals
if needed download using the "Get Adobe Reader" button at the following link
http://www.adobe.com

You may wish to bookmark this link in case of future issues
Review Chapter 14 under the Users guide that can be found in Drivers and downloads Date and time are in user settings.

http://www.usa.canon.com/consumer/controller?act=ModelInfoAct&tabact=SupportDetailTabAct&fcategoryid=241&modelid=9986#SupportDetailAct