How reset passsword.? router

Access the management page from your browser. (Internet Explorer, Firefox, Etc.)

The address is: 192.168.1.1

The default password is admin, leave the username blank

Click on the "Wireless " link

Then click on "Security"

You will see your WEP key there.

If you have forgotten your router passsword, you will need to reset the router.

Linksys reset

The easiest method of resetting your Linksys router's password is to reset your router back to the default factory settings. This is done by simply holding down the reset button located on the back of the unit for at least 30 seconds. Once the router has been reset, it must be reconfigured. Using your web browser go to URL address http://192.168.1.1. You will then be prompted to login to your router. A log-in screen asking for the password will automatically appear. At this time enter the default password "admin", in lower case letters into the password field. The username field may be left blank at this time. (Note: both the default username and default password are set to "admin" on some of the newer Linksys router models).

If I could be of further assistance, let me know. If this helps or solves the issue, please rate it and give a testimonial for my response

Thanks, Joe

I’m happy to assist further over the phone at https://www.6ya.com/expert/joe_8b8c2cd6ce148309

Hi

There is 2 Usernames when it comes to Routers.

1st is the USERNAME and Password you use to get into the Router configurations which is the following.
Username: admin
Password: admin
The above username and password is the Factory setting and only the password can be changed by an user. SO if it was not changed the password will still be admin or you can reset the modem to reset the password back to admin.

2nd is the Username and Passsword you get from your Internet Service Provider which usually is the email address and whatever password you gave them to set your internet up

Hi,
This issue can be resolved by reseting the router.You might see a reset password option on the back side of the router.
Please reset the router by placing a pin in reset hole and push the pin slightly, (remember you need to do this when the router is in ON state)
Then connect your router to your computer using Ethernet port (this is for configuration) and also connect the ADSL cable.

now open internet explorer and type in //192.168.1.1
Then it will prompt you for user name and password
Username: admin
Passsword: password
this username and password is by default.

Thanks,
Satheesh

Hi,
This issue can be resolved by reseting the router.You might see a reset password option on the back side of the router.
Please reset the router by placing a pin in reset hole and push the pin slightly, (remember you need to do this when the router is in ON state)
Then connect your router to your computer using Ethernet port (this is for configuration) and also connect the ADSL cable.

now open internet explorer and type in //192.168.1.1
Then it will prompt you for user name and password
Username: admin
Passsword: password
this username and password is by default.

Thanks,
Satheesh

Hi,
This issue can be resolved by reseting the router.You might see a reset password option on the back side of the router.
Please reset the router by placing a pin in reset hole and push the pin slightly, (remember you need to do this when the router is in ON state)
Then connect your router to your computer using Ethernet port (this is for configuration) and also connect the ADSL cable.

now open internet explorer and type in //192.168.1.1
Then it will prompt you for user name and password
Username: admin
Passsword: password
this username and password is by default.

Try leaving the username blank and just typing admin in the password. If you remember your old username and password try those too, You may not have saved changes.

The router password gets you into the utility program--the WEP password is the SSID allowing you to connect (wirelessly) to the router
Open INTERNET EXPLORER and. (In the URL address field), enter the IP address for your wireless router ( the DEFAULT GATEWAY. This information should be contained in your router's manual. If you cannot find it, enter "198.168.1.1" as the address. This is usually the default IP address for most routers.do not type "www" just the number
Enter the username and password for your router. This should also be supplied in the router's manual. If you don't have this information, go to routerpasswords.com and find the brand and model of your router. This site lists the default login information for most wireless routers you can try "ADMIN" for user name and "PASSWORD" for passsword.
You should now be able to see your wireless router settings. You can configure your network ports, as well as SSID (wireless network name) and passwords.

OR YES YOU CAN ALWAYS RESET TO THE "OUT-OF THE BOX" SETTINGS BY PRESSING THE TINY RESET BUTTON ON THE BACK (need paper-clip)

Please reset the router by placing a pin in reset hole and push the pin sslightly, (remember you need to do this when the rrouter is in ON state)
Then connect your router to your computer using ethernet port (this is for configuration) and also connect the ADSL cable.

now open internet explorer and type in //192.168.1.1
Then it will prompt you for username and password
Username: admin
Passsword: password
this username and password is by default.

then configure your router as you need by changing display name, password authentication, MAC registration etc...

If you face problem with connecting internet even following the above steps, then you need to contact ISP(internet service provider) for settings.

Thanks,
Satheesh

The common username and password are the following:

Username :admin
Password :admin

Username :admin
Password :password

If these does not work try to reset the router to factory default and then the same would work

In order to reset either there would be a dedicated reset button either on front or back of the router,or there would be a reset hole where u need to put in a pin and hold it for 20-30 seconds, if none of them are available press the power button and keep it pressed for 40 - 50 seconds, it should work

Default user name and password is "admin"
Otherwise, you can use the reset button on the back to restore the default settings including the default password.

If this helps, please vote for my solution.