Question about Konica Minolta Office Equipment & Supplies
I want to replace the fusing unit in Konica Minolta bizhub C253
How to replace fusing unit in c253
Posted on Jul 13, 2019
POWER OFF MACHINE! Open the front door remove one screw from the small access UPPER RIGHT cover disconnect the three connectors two carry 120 VAC other sensor signals the open the right side of the machine two screws below the fuser and remove the unit. reinstall opposite direction. Be careful not to brake the sensor connector
Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f
Posted on Dec 27, 2015
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
Here's a link to this great service
Posted on Jan 02, 2017
SOURCE: c350 malfunction code c-0501
After replacing the fuser unit, if you got a c0501 code you must open the front door where the toner is. On the right side (hinge side) next to the black toner and drum unit there is a plastic pannel/cover. In the lower portion of that pannel there is a hole where a trouble reset switch is loacted. With a flashlight you may be able to see it. You are ment to use a thin screw driver or the like to push the button. You do this while the machein is on and desplaying the code. As soon as you press the button the copier will clear the code and start warming up. Thats it! If you are un certin of the button placement you can take out three screws from the pannel and loosen one screw from the pannel above it and and pull the pannel off the unit. You will see the board and it is the button on the (left), as there are two of them. Tho you only have access to the one thru the cover.
Posted on Oct 18, 2009
tis error means abnormal tonder density in the balck image unit take the blacke image unit out and shake it while holding it level and put it back in the machine to reset the error code leave the machine on and open then close the front door
Posted on Nov 16, 2009
C-3421 = Fusing heaters trouble
1. Turn OFF the main power switch.
2. Turn main power switch ON while pressing the Utility/Counter key.
3. Touch [Trouble Reset].
4. Check to make sure that [OK] is displayed and the it has been reset.
5. After turning off the main power switch, turn it on again more than 10 seconds after and check if the machine starts correctly.
If error code returns a technician is needed to replace fuser section. Call local dealer with error code and tell them to make sure a tech brings a fuser assembly.
Posted on May 19, 2010
Este código significa que la vida las partes de su desarrollo + unidad de imagen se ha caducado. Ahora es el momento de reemplazar las partes.
Posted on Jun 19, 2010
Tips for a great answer:
Jun 27, 2016 | Konica Minolta Bizhub C253 Copier
Nov 14, 2015 | Konica Minolta Office Equipment & Supplies
Sep 01, 2014 | Konica Minolta Bizhub C253 Copier
Aug 21, 2014 | Konica Minolta Minolta Bizhub C253 Copier
Feb 12, 2014 | Konica Minolta Minolta Bizhub C253 Copier
Jan 25, 2014 | Konica Minolta Minolta Bizhub C253 Copier
Jan 17, 2014 | Konica Minolta bizhub C250 All-In-One...
Aug 06, 2013 | Konica Minolta Bizhub C253 Copier
Jan 24, 2011 | Konica Minolta bizhub C250 All-In-One...
Mar 31, 2010 | Konica Minolta bizhub C250 All-In-One...
Oct 05, 2019 | Konica Minolta Office Equipment & Supplies
109 people viewed this question
Usually answered in minutes!
Level 3 Expert
Level 3 Expert
Level 3 Expert