It stops cooking and gives me a F1 code - GE Advantium 120 Convection/Microwave Oven

Error Code/Message - Oven - F1 Error Code - F1 E5

Control displaying F1 E5:

There may be a problem with the Oven Control, or the associated wiring.

Power unit down by turning off the circuit breaker(s) for one (1) minute.

Power unit up by turning on the circuit breaker(s).

Monitor the oven for one (1) minute to ensure the error code does not display again.

Verify oven operation.

Dear n2disney2,

I wll need to know the make and model number for this appliance and then I can give you the instructions that you need.

To answer your question and this is purely "guesswork" without knowing the make and model of your appliance, but I would have said that this "F1" that you have is some kind of inbuilt/ programmed variable that your oven has. Its either going to be a cooking time, or some kind of function method for either cooking, defrosting or power setting; as a lot of ovens have a variable wattage (power) setting, thus allowing you to select the level of radiation you want to expose your food to.

Anyway, Like I said, if you can provide me with the manufacturer and model details of this appliance, then I can best serve you on this.

I look forward to hearing from you soon, and hopefully we can resolve your query.

Yours sincerely

Oz

Hello there:
This is a oven sensor problem in the microwave
I would contact your nearest appliance dealer for parts support and replacement advise
F1 Open sensor, will occur below 190F of cavity temperature within 15 minutes after starting convection, combination or roast cook Check oven temperature sensor for continuity. Replace if zero or infinite ohms

Hi,

Many models of the GE microwave have sensors that can detect humidity from the foods you are cooking. This allows the microwave to make adjustments to the power levels used to cook your food. If "Sensor Error" appears, you should either press "Clear" to cancel the mode or leave the food in the appliance longer to give the microwave more time to detect the food.

Press "Time Cook" to manually enter the time if you receive an error message when trying to use the "Sensor Reheat" mode of your GE microwave. The error message may be caused by the food item being too large or too small to detect.

these are some other code error that will help you in case of next time.

1. Step 1 Press "Off/Cancel" (or "Cancel/Off" depending on your model) to clear the error code. Note the code if it reappears.
   
2. Step 2 Replace the touchpad if the code displayed is "F0," "F7" or "F10." A function key is stuck or shorted.
   
3. Step 3 Replace the touchpad or the clock (ERC) if the code "F1" is displayed. Disconnect the ribbon connector to the touchpad. If no code is displayed after an hour, replace the touchpad. If the code displays again, replace the clock.
   
4. Step 4 Replace the oven temperature sensor if "F2," "F3" or "F4" is displayed. "F2" indicates the oven temperature is too hot and the oven temperature sensor is suspect. "F3" or "F4" indicates the oven temperature sensor or shorted or open.
   
5. Step 5 Replace the ERC if "F5," F6" or "F8" is displayed. The ERC is the main control unit. "F5," F6" and "F8 are codes that indicate problems in the ERC functions.
   
6. Step 6 Inspect the door-lock assembly and circuit if "F9" is displayed. The door must lock when the oven is in use. If the lock mechanism is not functioning or if the detection circuit is malfunctioning, the stove will display "F9."
   

jQuery('.article ol .image').each(function(i,e){ var $this = jQuery(this); $this.find('img').error(function(){ jQuery(this).remove(); $this.remove(); }); }); NOTE:


"F3" codes mean your oven temperature sensor has failed or shorted out. The only thing you can do is to replace the sensor.

Take care.

Here is some wisdom for understanding F1 fault codes.

In some models, there are subcodes that make diagnosis even easier.

Here's a simple explanation of what's going on and how to troubleshoot:

The F1 code indicates that:


a. The electronic range control (ERC) is sensing heat in the oven when in a time-of-day (i.e., not cooking) mode.

b. The ERC is receiving information to run multiple heat functions simultaneously.


Although different components (depending upon the model) could generate the code, simple and straightforward testing using your ohm meter is all you gotta do to test for it.

1. Check the oven temperature sensor. The oven sensor has to be within spec or it will cause the F1 code.
As an example of being out-of-spec, the ERC will generate an F1 fault code when the sensor shows 1650 ohms during a time-of-day mode.
This is equivalent to 350°F in the oven.
The resistance isn't high enough to generate an F2 code (runaway temp) or an F3 or F4 code (shorted/open sensor circuit).
The ERC monitors the sensor circuit after a heat cycle and expects the resistance to drop back to 1050-1100 ohms.
The fault code is generated when this doesn't happen. Checking the sensor circuit means also checking the harness,
harness connections and the sensor itself.

2. If the oven sensor circuit checks okay, then turn your inquisitive eyeballs to the touchpad.
If the range has a separate touchpad/keyboard, the keypad may have moisture that is shorting several circuits simultaneously.
If the F1 code is given immediately (instead of during or after a heat cycle),
remove the ribbon connector from the touchpad to the ERC after clearing the F1 code. If the F1 code does not return in five minutes,
then cast a suspicious gaze upon the touchpad/keyboard. Shorts may be caused by using an ammonia-based glass cleaner.
The touchpad surface will absorb ammonia-based cleaners that are sprayed directly on the glass surface. When heat is applied,
the surface material can break down causing shorts.
If you're gonna use ammonia-based cleaners on your control panel, then you should spray it on the rag and then wipe the touchpanel
-don't spray directly onto the surface of the touchpad.

3. On Amana ranges with a rotary temperature dial, be sure that the knob is in the OFF position when performing tests.

4. If these tests all check good, then replace the ERC.


Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question.
@#@EWR

Here is some wisdom for understanding F1 fault codes.

In some models, there are subcodes that make diagnosis even easier.

Here's a simple explanation of what's going on and how to troubleshoot:

The F1 code indicates that:


a. The electronic range control (ERC) is sensing heat in the oven when in a time-of-day (i.e., not cooking) mode.

b. The ERC is receiving information to run multiple heat functions simultaneously.


Although different components (depending upon the model) could generate the code, simple and straightforward testing using your ohm meter is all you gotta do to test for it.

1. Check the oven temperature sensor. The oven sensor has to be within spec or it will cause the F1 code.
As an example of being out-of-spec, the ERC will generate an F1 fault code when the sensor shows 1650 ohms during a time-of-day mode.
This is equivalent to 350°F in the oven.
The resistance isn't high enough to generate an F2 code (runaway temp) or an F3 or F4 code (shorted/open sensor circuit).
The ERC monitors the sensor circuit after a heat cycle and expects the resistance to drop back to 1050-1100 ohms.
The fault code is generated when this doesn't happen. Checking the sensor circuit means also checking the harness,
harness connections and the sensor itself.

2. If the oven sensor circuit checks okay, then turn your inquisitive eyeballs to the touchpad.
If the range has a separate touchpad/keyboard, the keypad may have moisture that is shorting several circuits simultaneously.
If the F1 code is given immediately (instead of during or after a heat cycle),
remove the ribbon connector from the touchpad to the ERC after clearing the F1 code. If the F1 code does not return in five minutes,
then cast a suspicious gaze upon the touchpad/keyboard. Shorts may be caused by using an ammonia-based glass cleaner.
The touchpad surface will absorb ammonia-based cleaners that are sprayed directly on the glass surface. When heat is applied,
the surface material can break down causing shorts.
If you're gonna use ammonia-based cleaners on your control panel, then you should spray it on the rag and then wipe the touchpanel
-don't spray directly onto the surface of the touchpad.

3. On Amana ranges with a rotary temperature dial, be sure that the knob is in the OFF position when performing tests.

4. If these tests all check good, then replace the ERC.


Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question.
etry$

Hi,
The failure code list says to replace your Electronic Oven Controll. Contact a Frigidaire parts dealer and check the price and availability.
You will need to give them your make and model number.
Buckle up! It may get expensive!

Good Luck!

GE
Microwave Fault Codes Failure
Code Condition Check/Repair F1 Open sensor, will occur below 190F of cavity temperature within 15 minutes after starting convection, combination or roast cook Check oven temperature sensor for continuity. Replace if zero or infinite ohms F2 Shorted thermal sensor, will occur if a shorted thermal sensor is detected continuously over 5 seconds on convection, combination or roast cooking Check oven temperature sensor for continuity. Replace if zero or infinite ohms

Note: It will take a minimum of 5 minutes of convection run time before F1 or F2 code will be displayed if the thermal sensor is shorted or open. F3 Shorted key panel (touch pad), will occur if a shorted key panel is detected continuously over 60 seconds Replace key panel (touch pad) F4 Open humidity sensor, will occur if humidity sensor is detected as being open continuously over 5 seconds Replace humidity sensor F5 Shorted humidity sensor, will occur if humidity sensor is detected as being shorted continuously over 5 seconds Replace humidity sensor F6 Shorted temperature probe, will occur if temperature probe is detected as shorted continuously over 5 seconds Replace temperature probe ProbEe Open temperature probe, will occur if temperature probe is detected open, or not plugged into the receptacle If probe is plugged in and "ProbE" is on display check continuity of the probe with an ohm meter. If zero or infinite ohms, replace it

Here is some wisdom for understanding F1 fault codes.

In some models, there are subcodes that make diagnosis even easier.

Here's a simple explanation of what's going on and how to troubleshoot:

The F1 code indicates that:


a. The electronic range control (ERC) is sensing heat in the oven when in a time-of-day (i.e., not cooking) mode.

b. The ERC is receiving information to run multiple heat functions simultaneously.


Although different components (depending upon the model) could generate the code, simple and straightforward testing using your ohm meter is all you gotta do to test for it.

1. Check the oven temperature sensor. The oven sensor has to be within spec or it will cause the F1 code.
As an example of being out-of-spec, the ERC will generate an F1 fault code when the sensor shows 1650 ohms during a time-of-day mode.
This is equivalent to 350°F in the oven.
The resistance isn't high enough to generate an F2 code (runaway temp) or an F3 or F4 code (shorted/open sensor circuit).
The ERC monitors the sensor circuit after a heat cycle and expects the resistance to drop back to 1050-1100 ohms.
The fault code is generated when this doesn't happen. Checking the sensor circuit means also checking the harness,
harness connections and the sensor itself.

2. If the oven sensor circuit checks okay, then turn your inquisitive eyeballs to the touchpad.
If the range has a separate touchpad/keyboard, the keypad may have moisture that is shorting several circuits simultaneously.
If the F1 code is given immediately (instead of during or after a heat cycle),
remove the ribbon connector from the touchpad to the ERC after clearing the F1 code. If the F1 code does not return in five minutes,
then cast a suspicious gaze upon the touchpad/keyboard. Shorts may be caused by using an ammonia-based glass cleaner.
The touchpad surface will absorb ammonia-based cleaners that are sprayed directly on the glass surface. When heat is applied,
the surface material can break down causing shorts.
If you're gonna use ammonia-based cleaners on your control panel, then you should spray it on the rag and then wipe the touchpanel
-don't spray directly onto the surface of the touchpad.

3. On Amana ranges with a rotary temperature dial, be sure that the knob is in the OFF position when performing tests.

4. If these tests all check good, then replace the ERC.


Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question.
^&^%tg