Can fixya repair an at&t answering machine 1339

These machines are not user serviceable, no parts will be available to the general public. Have a trained service technician give you an estimate for repairs.
Cheers,
Embroidery Services
San Diego, CA

it seem issue with the water senser.

Repairing a Janome or New Home Sewing Machine ...

www.thriftyfun.com/Repairing-a-Janome-or-New-Home-Sewing-Machin...

Question: Memory Craft Machine Won't Run ... I'm a computer repair technician and good with tools, is this something I could fix or should we .... machine which will zig zag fine if i turn the wheel by hand or sew very slowly; as soon as I speed ...

Janome won t turn Sewing Machines Questions & Answers ...

www.fixya.com > Forum > Tags > won t turn > Sewing Machines

Janome sewing machines won t turn related questions and answers. ... Ad. Question about Memorycraft 6500P Computerized Sewing Machine ... it could be a part has worn or broken, esecially when the hand wheel won't turn,, it needs to be.

Janome wheel not turning Sewing Machines Questions ...

www.fixya.com > Forum > Tags > wheel not turning > Sewing Machines

Janome sewing machines wheel not turning related questions and answers. ... 10000 janome jamming fly wheel won't turn fly wheel won't turn warning for too thick ...the hand wheel is not moving the needle at all Hi I was unable to move the needle at all ... Janome Memory Craft 9000 Computerized Sewing Machine.

Chrysler Laser fuel filter location Questions & Answers - Fixya

www.fixya.com > ... > fuel filter location > Cars & Trucks > Chrysler

Chrysler Laser cars & trucks fuel filter location questions and answers. ... i need to know where the voltage regulator is located on my 1986 chrysler lasr 2.2 l ...

Mitsubishi MSZ-GE06NA Mr.... Repair Questions - Fixya

www.fixya.com/.../p3677512-mitsubishi_msz_ge06na_mr_slim_wall_m...
Recent Mitsubishi MSZ-GE06NA Mr. Slim Wall Mounted Indoor Unit Air Handlerquestions, problems & answers. Free expert DIY tips, support, troubleshooting ..

Bosch Tassimo T65 Repair Questions,... - Fixya

www.fixya.com > ... > Coffee Makers & Espresso... > Bosch > TASSIMO

0 Answers. Water sat in the bottom tray of my tassimo t65 and now it has two red lights flashing can I fix it · Bosch Tassimo... ' Posted on Aug 23, 2014 ' Be the ...

Bosch TASSIMO red light water full Unsolved Problems - Fixya

www.fixya.com/unsolved_problems/red_light_water.../tassimo

0 Answers. Water sat in the bottom tray of my tassimo t65 and now it has two red lights flashing can I fix it. Aug 23, 2014 ' Coffee Makers & Espresso Machines.

Bosch TASSIMO cleaning condensation tray Unsolved ...

www.fixya.com/unsolved_problems/...condensation_tray/.../tassimo

For an answer to this question, you will have to inquire through the manufacturer, or perhaps, there will be a advertiser who does this type of work whose name will come to you along with this answer. Look around on this page right now.

FixYa.com is not a parts or repair depot.

Thanks for your question today at FixYa.com

i believe all you need to do is unplug it or take it out of answer mode. keep in mind you have to unplug the phone line as well as it will get power from it.

robert

The rL error code during the clean cycle is likely caused by friction on the spin basket shaft since you indicate that you hear squeaking when the washer is spinning. The squeaking is normally caused by a bad bearing in the rear tub shell. I recommend that you have the washer diagnosed and repaired by a Sears service technician. This type of problem will normally require an extensive tear down of the washer to repair. It is not a problem that you can normally repair yourself.

Open the door & slowly rotate the spin basket to see if you can feel any kind of drag on the bearings. If the bearings check good, the control board is sensing a load & will need to be replaced.

Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question

I believe that the 4 is because there is a wiring issue with one of the microswitches where the damper motor is, and it will not allow the damper / control board to recognize "open" position.

Replacing the damper - will probably NOT clear the code. The problem lies in the controller board.

Many times this happens after a water filter change (bad location) and spilling water - short circuiting the board.

If this is under warranty still - have them come out and fix it.

If you are not capable of this repair - have it serviced.

If not, and you are comfortable working on appliances - CLICK HERE for a blowup diagram of the controller unit.

#38C and #38 are the controller boards.



Thanks for using FixYa - a FixYa rating is appreciated for answering your FREE question.