How do you cut the intercom volume down? Every time the nurses at my job talk over the intercom, my patients and I cringe because the volume is so loud. Is there a way to cut it down on my side and ad

look for personal care attendant courses.

in Austalia it is http://www.hsta.vic.edu.au/courses/certificate-iii-in-aged-care?gclid=CJnDxb2HwcgCFYgsvQodZ64CoQ
Aged care Certificate iii
jobs are advertised as PCA
university also have courses in aged care nursing
http://www.unimelb.edu.au/online/ageing/masters/?utm_source=google&utm_medium=paidsearch&utm_term=Master&utm_campaign=ageingsept2015

To Page another phone to initiate intercom:-

From the base station - press Find hs/Intercom.
From a handset - Press Intercom/clear.

Then select the station you want to talk with or All to
page all stations at the same time.

To answer a page:-

From the base station - press Find hs /Intercom or Speaker.
From a handset - press Intercom/clear or Talk/Flash.

Hope this helps

Ive also included a link to the D1785 Series User's Guide








http://www.uniden.com/content/ebiz/uniden/resources/ownersmanuals/D1785om.pdf

1. Use the (M) Auto-Firm Button. Press the Auto-Firm Button to engage auto firm. The Mattress will become firm for nursing procedures. An indicator lights to notify the bed is in Auto-Firm mode. A timer will cancel auto firm in 30 Minutes. Should the nurse be called away, an unattended patient will not be left on a firm surface.
2. Set the patient weight with the Weight selection buttons (G).
3. Press the "Center" static Turning Mode button (I).
4. Place the patient on the bed.
5. Center the patient on the bed from side-to-side and head-to-foot.
6. Use a regular pillow under the head for comfort and to prevent the head from rolling excessively.
7. Raise side rails.
8. Press the desired Turning Mode button (O).
9. Press the Full Turn Range button (J).
10. Set the Turn Interval time with the up/down buttons (L).
11. If the patient feels the bed is too soft/hard press the up/down Comfort Range buttons accordingly (H).

Making an intercom call
1 Press {INTERCOM}
2 Select the handset you want to page
by pressing the desired handset
number ({1} – {6}).
To stop paging, press {OFF}.
3 When you finish talking, press
{OFF}.
Answering an intercom call
1 Press {handset icon} or {speaker icon} to answer the
page.
2 When you finish talking, press
{OFF}.
Note:
When the ringer volume is set to off,
the handset rings at the low level for
the intercom calls.

It is possible. I have ATT 945(?) 4 line phones that communicate via a DSL-like signal between units to do special things like intercom, etc.

What I have in my setup is that I have a seperate line from the point of entry of my phone line to my DSL modem.

I then have TWO stacked DSL filters PER LINE that feed the main phone line running to all the phones.

Be AWARE that when using the speaker phone there is a modulation of the gains both directions. When you talk OR have a noisy background noise, the gain of the speaker is cut down to prevent feedback. And when you go silent, the speaker gain is increased for you to hear the other side of the call. Essentially it takes as much discipline as the old two-way radios... one talker at a time with these speaker phones AND very little background noise.

Depends on the type of test he is using and if you are a male or female. Normal serum iron values are 75- 175 micrograms/dL for a male and 65-165 micrograms/dL for an adult female.
Did the doctor prescribe treatment? Low iron is an indicator of iron deficiency anemia. PLEASE ask your doctor for his recommendation.
As a side note, I have a real problem with a nurse disclosing test results to any patient. They are NOT the doctor.... All test results should be discussed between the patient and the doctor. HIPAA rules may have been violated here (Your patient rights)..

The left intercom button is the intercom button above the up volume control and to the left of the second intercom button.

March 25, 2013 - INTERCOM INSTRUCTIONS
Here is the answer! Press the INTERCOM button one time.
The INTERCOM display will show on the screen.
Use the UP or DOWN arrow button to select the HANDSET number.
Press the MENU/SELECT button to ring the HANDSET selected.
Press the END button when done talking