WHEN MY WHIRLPOOL BUILT IN OVEN MODEL RBS305PRS00 IS BAKING IT SOMETIMES CUT OFF AND YOU HEAR A CLICKING NOISE AND IT WILL DISPLAY EO F3.I CAN TURN THE OVEN OFF AND IT WILL BEEP AND DISPLAY EO F3.AFTE

The oven temperature sensor may be failing or defective. First, check sensor harness and harness connection between oven sensor and oven control to see if there is an issue with loose wires or visible damage to the wiring, such as a burnt wire.

Since the sensor is new, I'd check the wiring between the sensor and the control board. You need to check for any breaks (loss of continuity). Check the connections for the wiring harness for bent pins or corrosion.

(If you want to rule out a bad sensor, unplug it. Then check the resistance across the pins. Also check for a short between the sensor case and each of the two pins.)

If the sensor and wiring are good, then the control board is probably faulty. Unfortunately, that part isn't available at most sites. There may be some rare places that rebuild or have re-manufactured the electronic control.

I hope this helps.

Cindy Wells

Typically, as in ours, there are screws holding the inner door cover on. Look on the back, bottom or sides. These will hold the inner door on, then once removed, observe screws, typically Philips, holding the glass frames together. Careful not to over tighten the frames when reinstalling or you may crack the glass. Do not use a power screw gun either.

The F3 E2 error means that the oven high temperature sensor is reporting an over-temperature event. This could be a problem with the sensor, the oven control unit or the wiring. The oven needs to be unplugged (or the circuit breaker turned off) and then you can check the sensor. Since this is a built-in oven, you may want to get a professional to look at it. The oven has to be pulled out of the cabinet; if you do it yourself, make sure to get another person to help.

You need to open the rear access panel that covers the control (ERC) and the lower panel over the back of the range. Then find the sensor and trace it's wiring up to the ERC. Disconnect the wires from the ERC. Then with a multimeter, check the resistance of the oven temperature sensor. It should give a reading of 1000-1200 Ohms. Then the ERC may be faulty.

However, some people report that just disconnecting and then reconnecting the wiring will solve the issue. In that case, a bit of debris may have gotten into the wiring harness.

I hope this helps.

Cindy Wells

Marty, is your control board located in the door in the itself?

This is typically the oven sensor that is bad. The sensor is the pencil size probe in the oven. They usually can be pulled out from the front. and have a disconnect clip. very easy to replace.

Have you tried pulling the connectors off the control board and reinserting them. If you still have problems the control board could be the issue.

Hello,4 Digit Failure Code F0 - E0 Analog to Digital Failure Disconnect for 30 seconds - if display re-appears - replace control F1 - E1 Safety flip flop Replace Electronic Range Control/Clock(ERC) F2 - E0 Shorted keypad Replace Electronic Range Control/Clock(ERC) F3 - E0 Oven temperature sensor or oven temperature sensor fuse opened Replace oven temperature sensor or fuse F3 - E1 Oven temperature sensor shorted Replace oven temperature sensor F3 - E2 Oven too hot Replace oven temperature sensor F3 - E3 Clean temp too hot Replace oven temperature sensor F5 - E0 F5 - E1 and E2 Check door/latch switch Replace component 2 Digit Failure Code F0 or F1 or F5 Failed transistor Replace Electronic Range Control/Clock(ERC) F2 - E0 Oven temp too high 1. Test operation of door lock on self-clean models
2. Test relay contact operation
3. High resistance in oven temperature sensor F3

Thanks

F3 - E0 Oven temperature sensor (RTD) opened (upper oven, if double oven) Replace Oven temperature sensor (RTD)


If you need further help, I’m available over the phone at https://www.6ya.com/expert/craig_3fa289bf857b1a3c

i have a whirlpool gas accubake range and only two burners will ignite. The other two burners make a clicking sound and release gas but never light. I have to use a match to light the other two burners and the flame is uneven on one. What should i do?