Why am being cut off on you tube while watching dvds and when I retry to open I fail to get back on

If your Cricut machine is not cutting all the way through your material, or is only scoring the material, choose a machine below for specific troubleshooting tips. Fortunately this issue can usually be resolved with basic troubleshooting.

• Cricut Explore
• Cricut Personal, Cricut Create, Cricut Cake, Cricut Cake Mini, Cricut Expression
• Cricut Expression 2, Cricut Imagine
• Cricut Mini

correct cut settings.

Remove the blade housing, then remove the blade and ensure that there are not any bits of paper stuck to the blade or lodged inside the blade housing. Ensure that you replace the blade housing correctly into the machine. Once clean, test your cuts again. If the blade and housing are already free from debris, or cleaning it did not help, proceed to 3.

Try an arm buoyancy test: gently press down on the black arms that surround the blade housing and then release them. Do they bounce right back up, or do they stick or rub in any way? If they stick or rub, please contact Customer Care through one of the options below for further assistance. If they bounce right back up when released, proceed to 4.

Increase the machine pressure settings and try your cuts again. If this does not change the cut result, proceed to 5.

Increase blade depth by turning the dial at the top of the blade housing. If this does not change the cut result, proceed to 6.

Perform a Hard Reset on the machine. If this does not help, proceed to 7.

Check your machine's firmware version. If the firmware is not up to date, perform a Firmware Update using Cricut Craft Room, a Gypsy device, or Cricut Design Studio.

Retry your cuts with a new blade housing.

If the machine is still not cutting through materials, or is only scoring the paper, please contact Customer Care through one of the options below for further assistance.

Forced Firmware Update on the machine through Cricut Sync.

Retry your cuts with a new blade housing. If the issue persists, proceed to 8.

Attempt a Format and Restore on the machine through Cricut Sync. Please note that this step should only be taken if all other steps have failed to resolve the issue.

If this does not resolve the issue, please contact Customer Care through one of the options below for assistance.

new blade. If this does not help, proceed to 5.

Adjust/increase the Multi-Cut setting in the Cricut Craft Room cut preview screen and retry your cuts. If this does not change the cut result, proceed to 6.

Retry a cut using a new blade housing.

If the machine is still only scoring or not cutting through the material, please contact Customer Care through one of the options below for assistance.

black after 15mins is psu fail

replace ALL the electrolytic capactiors on the psu
this includes the mains 350 or 400V types
then retry....

try to find any faulty CCFL tubes using there feedback
from each ccfl transformer

you could just find one tube has failed

look too you tube for CCFL replace etc etc
look more to a faulty single tube here

water level pressure switch tube is clogged with lint or bladder in pressure switch is bad. disconnect power to washer open timer console look for a clear rubber hose disconnect fron switch and blow in tube a couple times reconnect tube and put unit on drain and spin for a second then retrying unit for water level fill put washer on small load water size and test if it continues to fill replace pressure switch...

Possibly the image is corrupt download this http://thepiratebay.org/torrent/5012023/MICROSOFT.WINDOWS.7.ULTIMATE.7600.16385.RTM.X64.RETAIL.ENGLISH.D

Update your System drivers http://www.devicedoctor.com/device-doctor-download.php
Use Power ISO instead of imgburn http://www.poweriso.com/download.htm

Have a nice day

The water lever sensor/switch is not working and needs to be replaced. IT has a air tube that senses the water lever by pressure. It the tube is clear then the switch needs replaciing,, If they is a clog, clear it and retry before replacing it.

Two flashing red lights means it has overheated. Maybee it does have alot of ventilation but the dust may have ecumulated to an amount that can not escape the system case. Clean it really well with a can of compressed air and make sure fan is running in the back. Some fans fail but continue to spin so if it looks to slow it probably is. You can watch you tubes tutorials about opening and cleaning your console. Hope this helps. Good Luck.

often times you can just pull the vacuum tube off the switch and blow back thru it to clear. more stubborn clog may require removing tube from other end which would be on the induced draft motor and try to clear with a paperclip. then reinstall the tubing and retry

According to the log file, there was a spindle servo failure. The spindle servo is responsible for maintaining rotational speed accuracy. I'd say your drive is pretty much dead. See if you can read a disk in the drive. I wouldn't be surprised if it had a tough time just reading files.

You have a picture when you're watching a DVD, but none when you're watching regular cable? Does the audio appear to be okay?? Are you sure you've switched the inputs on the TV back to main???
Let me know..
Bill

good job