Question about Dewalt Tools & Hardware - Others

1 Answer

Dewalt 771 slips in all torque settings in low, but works in high setting

Dewalt drill/driver DCD771 Type1. When transmission is set 1 the clutch slips in all 15 settings, if you move selector to 2 the clutch seems to work as it should, is there problem with the transmission or something else?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Master:

    An expert who has achieved Level 3.

  • Master
  • 401 Answers

The clutch is defective , you can get replacement parts from dewalt. There are several dewalt service centers in the US

Posted on Jan 07, 2015

Ad

5 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
muttandjeff

Allen Neal

  • 359 Answers

SOURCE: dewalt dw056 motor working but no drive.

make sure the selector switch is in full rev or full forward and not in mid throw goose the trigger and turn the selector at the same time

Posted on Dec 17, 2008

richk169

  • 18 Answers

SOURCE: I have a IR 2130

This gun shouldnt have an adjustment. If you cfm's from your compressor are enough. Too low cfm's mean lower torque. If cfm is high enough for the gun rating then I would say the gun is bad.

Posted on Nov 14, 2010

Repair Ahjoshe

  • 885 Answers

SOURCE: dewalt dw297 impact wrench does'nt work at all. the cables does'nt seem broken, so don't know what to look for.

A good place to start with Dewalt tools is the switch. Take the front off the handle and pull the switch out far enough to test the posts on the back. Plug the cord in and check for voltage where the cord attaches to the switch. No voltage, bad cord, replace the cord. If you have voltage, the cord is good. With some help, hold the switch on and check for current on the motor side of the switch. If no voltage, replace the switch. If there is voltage there, you are going to have to check the brushes, armature and/or field for continuity or shorts.

Posted on Jun 28, 2012

Repair Ahjoshe

  • 885 Answers

SOURCE: repair intermittent switch on dewalt 20 Volt impact driver

Unfortunately Dewalt switches are solid state, meaning there is little to nothing you can do to fix them when they don't work. Occasionally spraying them with electronics cleaner and blowing them out with clean, dry air will make them work a little longer but more often than not you simply have to replace the switch. The part number for your driver is N084669. They cost between $65 and $75 so shop around or check with a local repair center.

Posted on Oct 24, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My Dewalt DC925 works well but the torque settings don't seem to be working.when i am drilling screws the drill will just drill until i release the trigger.is this a clutch problem?. Many thanks.


Try to put it on the lowest torque and if it slips when wanted, then add a little more torque and check to make sure it slips. Continue at each torque setting and usually works again at full torque. Usually happens when left on the same torque all the time. This kind of resets it.

May 07, 2015 | Dewalt Drills

1 Answer

Problems with torque clutch in new DeWalt tranmission


hi
like most clutches on hummer unit after the assembly has been done you will a way to tighten the spring clutch look for adjustment to make the spring looser and tighten

Mar 10, 2017 | Dewalt DC925 Cordless Drill

1 Answer

Type your problem for a solution...


I'm answering without knowing which model you have but, there are some Dewalt drills that will go into hammer and/or drill mode only if the speed selector is in 2nd gear. The torque settings are accessable only in driver mode. Short of that you may have broken parts in the transmission that can only be repaired by replacing the transmission.

Dec 28, 2011 | Dewalt Drills

1 Answer

The clutch is slipping how do i fix


If its clutching out in drill mode the clutch pin is worn. This part is 635718-00 its only a couple bucks. not hard to repair either bout 5 min.

Sep 07, 2011 | Dewalt DC988kar XRP 3 - speed 1/2" 18v...

2 Answers

The drill works but you can hold the chuck while operating the drill.


could be a couple problems, is the switch selector fully engaged in hi/low and is the clutch seting set for the proper torque.If both OK then I would have to think that you need a new clutch assembly

Jan 18, 2011 | Dewalt 18 Volt Compact Drill Kit

1 Answer

Using a garden auger with the torque set to the highest setting the clutch broke and started to slip. Is this too much for the Dewalt 720 cordless drill? Dewalt is repairing it under warranty.


Yes, luckily Dewalt is taking care of you. You might want to look into a 1/2' drive electric model (sorry with a cord) Alot depends on how hard the ground is but in the long run the big electric will handle about anything you throw at it. Check Sears or Home Depot both good sources for good tools

Jan 04, 2011 | Dewalt 18 Volt Compact Drill Kit

1 Answer

I got one of these drivers to replace my older driver. It clearly has more than enough torque, which is good in some cases but for some routine things around the house it is too much. Even on the lowest...


Most models have two selections, one for the clutch (which in effect regulates the torque applied) and the other is the gear selection ( usually a setting of 1, 2 & 3, with 1 being for driving screws and 3 for drilling purposes). In addition to those selections, the trigger controls the overall speed of the motor. These are all the control you have over the drill, granted the Dewalt tool is a bit torquey, but it is meant to be a construction tool.

Nov 23, 2010 | Dewalt 18 Volt Compact Drill Kit

1 Answer

Amount of torque per setting in dewalt dc925 xrp


The torque settings are not tightly controlled so they are not all that repeatable from drill to drill. They also vary somewhat with the speed of the drill and the condition of the battery. And they aren't linear (a setting of 10 is not twice the 5 setting) Simplest thing to do for a rough idea is to use your hand to hold the chuck still to feel how much torque you have at each setting. (start low and grip it tight!) If you want a specific torque setting, say 10 ft-lbs, then put a stout screw in a scrap of wood, hang a 10 lb weight on it 12 inches from the screw and adjust until it just starts to slip.

Apr 02, 2010 | Dewalt DC925B Heavy Duty Xrp 18V Cordless...

2 Answers

My dewalt drill won't drive


is your battery is fully charge or maybe your clutch setting are too low. set it drill mode if it is not working you need to replaced
trans/clutch assy

May 28, 2008 | Dewalt 18 Volt Compact Drill Kit

2 Answers

Dewalt 18V XRP Clutch Slipping


it very economical to repair the drill. replace the transmission.

Apr 27, 2008 | Dewalt 18 Volt Compact Drill Kit

Not finding what you are looking for?
Tools & Hardware - Others Logo

Related Topics:

239 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dewalt Tools & Hardware - Others Experts

John Trevino

Level 3 Expert

1420 Answers

Ruben Bustamante

Level 2 Expert

120 Answers

john h

Level 3 Expert

22486 Answers

Are you a Dewalt Tool and Hardware - Other Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...