Acurite wireless weather will not work new last season all new lithium batteries in right and were checked no picture #'s on screen

Question edited for a LOT more clarity. full 'make model (what it is)'.
Question moved from Computers to Model category.

Remove the batteries from both indoor and outdoor unit. Leave them out for 10 minutes. Replace the outdoor sensor with a new battery (2xAA), and then new batteries in the main unit (3xAA).

00605 Wireless Weather Station + Companion Instructions

AcuRite https://www.acurite.com > media > manuals > 0... PDF NOTE: When replacing the batteries for the wireless sensor, remove the batteries from the sensor and clear that sensor's channel on the main unit by pressing ...
6 pages

Hard Reset for Sensor Models 00606TX/06009RMA1 & ...

AcuRite https://support.acurite.com > en-us > articles > 360007...
The following reset steps can be performed to correct issues of the sensor not connecting to the display. Symptoms of the sensor not...
https://fccid.io/RNE00605TX/User-Manual/User-Manual-707183

..

My National Geographic Weather Station is the opposite. The outside sensor only indicates the temperature, but the single CR2023 battery lasts a year. The inside unit on my desk lasts around 5 - 6 months and lets me know if needs a battery by showing the outside temperature as ' -- '

Although the manual says 'rechargeable batteries are not recommended', I would try 4 Sanyo Eneloop batteries. Or you could contact Acurite Support and ask them if your battery use is excessive?

01602BPDI - Professional Weather Station Instructions

AcuRite.com https://www.acurite.com > 01602-instructions

Professional Weather Center model 01602BPDI. Questions? Contact Customer Support at. (877) 221-1252 or visit www.AcuRite.com. SAVE THIS MANUAL FOR FUTURE ...

Make sure that all the batteries are good!!
This procedure outlines the typical process to pair the sensor and base.
Base Station Battery Installation
·Remove the printed vinyl label from the LCD screen of the base station
·Position the remote sensor near the base station
·Open the battery compartment at the back of the base station and insert (2) AA batteries according to the polarity markings. Replace the battery compartment cover.
·Within a short time the RF signal icon (located to the left of the outdoor temperature channel indicator) will start flashing. This indicates that the base station is ready to pick up the RF outdoor temperature signal from the remote sensor. It will continue to flash for 3 minutes or until the signal from the remote sensor is detected.

Register the Remote Sensor
·Open the battery compartment at the back of the remote sensor and slide the channel selector switch to your desired channel. For the first remote you may select any channel, for additional remotes select any unused channel
·Insert (2) AAA batteries according to the polarity markings. Be sure to install the batteries in the remote within the time that the RF signal icon is flashing on the base station. 1541 WeatherGuide Wireless Weather Forecaster with Barometer

We would recommend a reset of your Weather Station. Please verify that you are using a good-quality, standard alkaline battery, and follow the steps below.

1. Remove the batteries from the outdoor sensor only.
2. In the outdoor section on the main unit, there will be a "CH" and number 1-3.
3. If on CH 1, press and hold the channel button on the back of the unit for 5 seconds.
4. Press and release the channel button one time, it should show CH 2.
   • If it does not change to CH 2, repeat steps 4 and 5.
5. Press and hold the channel button for 5 seconds.
6. Press and release the channel button one time, it should show CH 3.
   • If it does not change to CH 3, repeat steps 6 and 7.
7. Press and hold the channel button for 5 seconds.
8. Press and release the channel button one time, it should return to CH 1.
   • If it does not change to CH 1, repeat steps 8 and 9.
   ***Regardless of what channel you begin on, clear out each channel by holding the channel button and return to CH 1***
9. Reinstall batteries in the outdoor sensor.
10. Press and release the TX button.
11. Leave both units side by side for up to 30 minutes to gain a strong connection.

If you need any further assistance, please contact AcuRite Customer Support at 1-877-221-1252 or [email protected].

Have you changed the batteries on the outside sender unit?

how do i set my clock for accurite 00604RX

How do I change the clock from 24hr to 12 hr?

Double check the batteries and the direction in which they are installed. If there is one backwards in the sending unit that is outside, it will not send a signal. Also, there is typically one battery in the indoor unit that is responsible for receiving the signal from the outdoor unit. If all of the batteries are in correctly except that battery, you will see the display, but will not get the data transmitted from the outside sending unit.

Double check the batteries to make sure they are installed correctly. If one of the batteries in the outdoor sending unit is in backwards, it will not send the outdoor data. On the indoor unit, there is typically one battery that is used for receiving the signal from the outdoor unit. If all of the batteries are in correctly but that one, you will see the display and the indoor temperature information, but the outdoor information will not be displayed.