Question about Raymarine Rc435 Chartplotter

1 Answer

I have problems with my plotter Raymarine Rc 435 chart plotter.This plotter can not location my ship to do.What is problems?

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

    New Friend:

    An expert that has 1 follower.

  • Expert
  • 97 Answers

Be sure there isn't any aluminum in close proximity to your GPS antenna, or that your antenna is not to close to other powerful electronics. Aluminium reflects electromagnetic signals and other electronics emit EM fields as well causing disruption of your GPS signal reaching your antenna.

Posted on Oct 03, 2014

Ad

3 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Radoslav Segaric

  • 43 Answers

SOURCE: Display control unit frozen, display just reads standby

The reason is because the housingin is a little bit broken or throw the keypad water came inside yuor Display and after this the oxidation ha destroyed a part of the printid circuit or the switch of the keypad

Posted on Oct 13, 2009

Joe Hogan

  • 10865 Answers

SOURCE: My Raymarine 435 is showing

Hi. Here is a download of the manual http://www.raymarine.com/raymarine/SubmittedFiles/Handbooks/Navigation/81212_1www.pdf

go to page 18 to learn how to correct your issue. J.

Posted on Aug 23, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Raymarine C90w Chart Plotter replacement cursor - where can I get one or what's a substitute fix?


I wonder if you could use the C80 cursor from this one on eBay?

Raymarine C80 GPS FOR REPAIR or For Parts BAD SCREEN eBay

If not, technology moves on. I love my Humminbird 998 HDSi.

Apr 28, 2018 | Raymarine GPS

1 Answer

Raymarine dsm300 Circuit breaker keeps tripping g when connected to chartplotter


either the cord to the chart plotter is faulty or the chart plotter itself is dead short
have an electrician do an insulation test and circuit test on the cord and plotter unit

Jan 08, 2017 | Raymarine Boating

1 Answer

System haild


Take the Raymarine Rc 435 Chartplotter to a system or computer engineer for repairs.

Jan 22, 2011 | Raymarine Rc435 Chartplotter

1 Answer

My Raymarine C80 CHart plotter won't load.


Check to see if this is a power issue by connecting to shore power and fully charging your batteries overnight with instruments off. While still connected to shore power, with batteries fully charged, turn on C80 navigation system. If the loading screen comes on and does not reset, then try holding down the button immediately to the right of the red power button for at least 3 seconds to see if the system re-boots.

Apr 13, 2010 | Raymarine C80 GPS Receiver

1 Answer

The chart plotter worked perfect for 5 yeas,


I think you have a C- Map card (black colour)clean the contacts with a contactcleaner if it not works try the card somewhere else
The C-Map card have problems that they work for a while and than stops inside the card a some memorychips and they losing contact

Sep 27, 2009 | Raymarine A65 Combo GPS...

1 Answer

Problems talking to autopilot


I think you use the NMEA output to the autopilot .
The plotter shows you only when you have a seatalkconection with a Raymarine autopilot on you Plotter

Apr 06, 2009 | Raymarine E120 Multifunction GPS Receiver

1 Answer

Rl70c raymarine depth finder problem


fish finder transducer needs to be on before you boot your system. check your hsb cables and termination

Jul 12, 2008 | Raymarine RL70CRC GPS Receiver

1 Answer

RL70CRC crashes with new "Wide" C-map cartridge


get a new burn on the chip, I have seen this issue on a particular burn.

Mar 22, 2008 | Raymarine RL70CRC GPS Receiver

1 Answer

Raymarine GPS system HALT ! URGENT PROBLEM


To get back up and running you are going to have to reset the unit. This is from the handbook:

Note: Take care - factory reset clears allWaypoint and Route databases.
➤ To perform a factory reset:
1. Power off the unit.
2. Press and hold CLEARwhilst powering up until <Erase backup procedure>
is displayed.
3. Either press CLEAR to abort Factory Reset and resume normal
Power-Up or press ENTER to continue Factory Reset.
4. Press ENTER again; the unit restarts as for a first time PowerUpwith
all values reset to their original factory settings

When you hit port and have an internet connection, make sure you are running the latest software version, currently listed online as version 1.09. You can download it here:

http://raymarine.custhelp.com/cgi-bin/raymarine.cfg/php/enduser/std_adp.php?p_faqid=965

Sep 10, 2007 | Raymarine Raychart 435 GPS Receiver

2 Answers

Raymarine RL70CRC GPSRadar


Hi Matt,

There is a feature in these chartplotters called "Plotter Mode" that is often misunderstood and causes the exact problem you describe.

Press menu.....chart setup.....and scroll to the bottom until you see Plotter Mode in the list of options. It should be set in the OFF position.

If you have more than one display networked onboard check the setting in each one invividually.

What Plotter Mode does is allows the chartplotter system to access range scales not supported on the chart. It is not normally used for map-based navigation but more so for chartless electronic plotting (it can display routes, waypoints and track-recorder breadcrumbs.) open-ocean cruising, or for ultra-precise GPS operations (like a precision anchor drop, finding a very specific location etc. When plotter mode is on you can zoom in to a very, very small working area. The indicator it is enable is the cross-hatch background on the screen, the lack of map information, and the NO CHART DATA watermark on the screen.

Jul 30, 2007 | Raymarine RL70CRC GPS Receiver

Not finding what you are looking for?
Raymarine Rc435 Chartplotter Logo

Related Topics:

158 people viewed this question

Ask a Question

Usually answered in minutes!

Top Raymarine Boating Experts

The Knight
The Knight

Level 3 Expert

76171 Answers

Ekse

Level 3 Expert

13434 Answers

Gene Pitts

Level 2 Expert

159 Answers

Are you a Raymarine Boating Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...