I had my direct tv disconnected and now I can not get the tv to respond to the reg. visio remate

If there are no audio output jacks on set you are out of luck unless you want to open the set and hook up some wires directly to the speaker connections inside observing correct polarity.

Un plug the TV for 10 min and remove the bratty from the remount

If you need further help, I’m available over the phone at https://www.6ya.com/expert/omar_c87dacfef1e87642

Many Visio tv's have the same problem, and also reversed - picture and no sound. The quick fix is to disconnect the power cord at TV - then hold in the power button (usually found on left side 1/4 up from bottom of screen , located on the side/back of the set. a square button all alone) - hold power button in for 30 1,000 mississippi's, yes, that is what a Visio tech told me and it works. I was lucky enough to have the problem start before the 30 return policy ended at Walmart - decided I did not want a product that obviously has a chip failure coming soon! I exchanged for a Samsung and have not looked back!

Our Visio 42" flat screen TV did the same thing. It didn't happen that often but sometimes it would go darker or the sound would go off until I changed the channel or turned TV Off then back On. I contacted Visio through my warranty and they sent me a flash drive to install info on my TV. Did not fix the problems. A year later before warranty ended I contacted Visio again. They sent a huge box for me to pack my TV in to send to the warehouse where they fix everything. It took about 2 wks. to get it back. Worked fine for about 4 months and the problems continued. I will not buy another Visio TV. I found out that they had many problems with several models.

dont use your reciever to switch video inputs to your tv, plug player directly into tv, use coax or optical input from player to reciever for audio

Hello
Four digit universal remote code for Vizio TV is
0081
Direct Code Entry

1. Press and hold the SETUP button until the red indicator stays on, then release the SETUP button.
2. Press and release the desired Mode button (TV, VCR, etc.). The red indicator blinks, then stays lit.
3. Enter the 4 digit code from the code tables. Note: after a valid code entry, the red indicator turns off. For an invalid code, the red indicator flashes.
4. With your device on, press CHANNEL UP. If the device responds, no further programming is required. Note: If some buttons do not operate your device, try one of the other codes for your brand.

[edit] Code Search If after trying "Direct Code Entry" your device does not respond, or if your brand is not listed, try doing a search of the code library for your code by following these steps.

1. Manually turn on the device (TV, VCR, etc.) to be controlled.
2. Press and hold the SETUP button until the red indicator stays on, then release the SETUP button.
3. Press and release the desired Mode button (TV, VCR, etc.). The red indicator blinks once, then stays on.
4. Press the CHANNEL UP button repeatedly (up to 300 times) until the device to be controlled changes channel. The red indicator blinks, then stays lit.
5. Press and release MUTE to install the code. The indicator light goes off.

Most users will want to store VCR codes under the VCR button, Cable codes under CBL, etc. If you want to store a VCR code under CBL, etc., first follow the procedure for Direct Code Entry and press CBL in step 2 of Direct Code Entry, then enter ANY VCR code in step 3 of Direct Code Entry. Then follow the steps above for Code Search.
OK.

go to front of tv and bring up the menue then go to the reset to factory tab and reset the tv that will fix the prob and also check batt in remate

about a year ago our visio tv started having lines going up and down from the bottom to the top. we called direct tv and they could not find anything wrong with the cable. the problem got better and then worse. finally we called the tv repair man and he said it was the monitor and that it cost more to replace the part than it does to buy a new tv. that means after about a year that we purchased it the tv monitor was bad. now what do we do?

Direct Dish.... :p only outputs to your TV on channel 3 or 4. This leads to only using Direct's remote. I would suggest to try going over to DISH Network as their remote is much better and will work the TV......

I bought a 42" Visio LCD from Costco and used code 10030 and it worked. It is the code for Goldstar TV.