Video Card wont detect - ECS H61H2-M12 Elitegroup Ecs/1155/H61/2ddr3/Vga/M-Atx P/N: H61H2-M12 -

Do you know the make and model of your video card? If not you can try a video card detection. Once detected go to the site and download the latest video card drivers. Most likely it will be an AMD or NVIDIA card.

http://support.amd.com/en-us/download/auto-detect-tool
http://www.nvidia.com/Download/Scan.aspx?lang=en-us

Did you port forward your router so the video will get thru?

contacts maybe corroded on card use rubber eraser and gently rub contacts on card make sure no residue from eraser is left on card ie... blow on it check port on phone and use canned or compressed air and blow it out as well, hope this helps retrieve your data, try using some else's computer to download data or see if it is detected

use your PCIE card to boot-up from CMOS, then check your onboard vga, try to configure it by 1st boot is your onboard, if that wont work then maybe your onboard vga was already damaged, better to use pcie video card rather than an onboard because it lets you consume the whole amount of your memory unlike the onboard card.. THanks

Please install first the driver of your video card..

If that did not work, then try this:

Open your cpu, disconnect your video card from your motherboard, clean the contact point with moisten cloth and let it dry.. reseat the video card properly on the motherboard... connect the cable from the monitor to the video card..turn on the computer.. on the task bar a message will pop up: found new hardware; your hardware is installed and ready to use.. if that appear then your video card is ready, and resolution can be change..

There is also one reason why your video card cannot be detected.. Your system could be using an integrated graphics controller which your windows operating system provided for your motherboard video drivers.. you need first to delete that so that your video card will be detected and use by your motherboard.. how? try these steps..
1. On My Computer, right click and select properties.
2. Select Hardware tab, and click Device Manager.
3. On the list of device manager, click View menu and select Devices by type
4. Double click Display Adapters, to display the list of connected graphics adapter.
5. Disable the graphics adapter listed, by right clicking of the file name and select uninstall.
6. Now close any program and shutdown your computer..
7 Connect your video card to the motherboard and turn on your computer. Your computer will run its add new hardware device , just be ready with your driver files..


If you can give me the full detail of your video card and the operating system you are using then I can help you find the right driver for your video card..


If this help you fix your problem, would you please rate this solution...much thanks..

im having the exact same problem, i dont think my graphics card can display the video feed! i tried everything but to no avail... if you find out plz let me know

Very strange. Windows 7 detects all graphics cards :S

Try Windows Update again, do a Custom scan and see if it comes up.

If it doesn't, you can download the drivers from here.

Best of luck!

Replace the Discrete Video card. That's why your LCD didn't detect when you run the Diagnostic test. There 2 type of video cards available to Dell Inspiron 6400/E1505. Either you have a on-board video card or discrete video card. Mostly, the discrete video card is caused when you not getting video output to your LCD (completely dark as if it is off). Discrete video card is detachable and replaceable. Good Luck.

IT MAY NOT SUPPORT THE MFG OF THE TV, UNLESS IT DOES SUPPORT AND I DONT KNOW ABOUT IT THAN GOTO THE TV MFG WEB SITE AND SEE IF THEY HAVE ANY NEW DRIVERS FOR THE CARD AND MAYBE THE MFG OF THE TV MAY ALSO HAVE DRIVER FOR YOU VIDEO CARD SO IT CAN DETECT THE SIGNAL,
IM THINK IF YOU HAVE PAL, THERE ARE 4 DIFFERENT TYPE OF SIGNALS AND WITH THE NEW DEGITAL TV , VEDIO CARD HAVE SET THEM TO DEGITAL SETUP, NOT ANOLOG

I DONT KNOW A FEW THING TO HELP YOU FEATHER, TV AND VIDEO CARD YEARS OF MFG IN EACH DEVICE.

IN FEB 2009 WE SWITCHED FROM ANALOG TO DEGITAL TV,

WITH THE BOX YOU WILL NOT BE ABLE TO USE THE TV

Creative doesn't have Vista drivers for that video card so unless you use some hacked drivers it probably wont work.