How do i turn off mode of only dialing an sos

Question edited for clarity, correct typo, add spaces.

It is stolen? Did you find it? SOS Code or Emergency Mode is normally put on when the phone id reported stolen or if the monthly bill isn't paid or Pay As You Go has run out of funds.

Help in the link if none of the above is applicable.

https://www.google.com/search?q=Micromax+X250+mobile+phone.+Unlock+keypad+SOS+code

..

i have same of issue too on my P50V10.....i can said thats 100% occur and 100% because of lightning/electric failtrue,09's service manual listing is not suitable for V series,top of the line on the brand.its has another services manual for Vseries only,its said thats audio PVM SOS on A-board failtrue.i'm finding solution too.my set now all HDMI input is not working,otherwise rca input tool!VGA will having a 2~3minutes working fine,after that picture become shaking than auto off to protect mode!theres really blinking 14 times & i feel thats because a high voltage shock into TVset by HDMI input,resulting a A-board damaged!!
i come from HongKong & official dealer reply me an unacceptable repair cost.does here anyone can answer of the 'audio PVM SOS'?

MY PHONE NEED A PASS WORD ITS ON SOS AND NETWORK CODE

try to type 0000

found this tonight:
1 blink STV 5v sense DG Board
2 blinks 15v SOS D Board
3 blinks 3.3v SOS D Board
4 blinks Power SOS P Board
5 blinks 5v SOS D Board
6 blinks Driver SOS 1 SU / SD / SC Boards
(SC energy recovery circuit)
7 blinks Driver SOS 2 SU / SD / SS Boards
(SC floating voltage area)
8 blinks Driver SOS 3 SS Board
(SS energy recovery circuit)
9 blinks Panel Config. SOS
10 blinks Sub 5v SOS / Main 3v SOS DG Board
DTV 9v SOS / Tuner Power SOS
11 blinks Fan SOS PB Board
12 blinks Sound SOS H Board
13 blinks Communication error DG Board
with IC8001 (Pesks Lite 2)

Hello,
Your power supply board is dead, u know basic electronics' and soldering? Most of the times, the power supply board just have dead leakages gases capacitors.These capacitors always bulges up on it top,or puff up on it top.Replaced these gases leakages capacitors will get your TV power stable,and work again.Or tries websites like Shopjimmy.com,Ebay.com to buy a whole refurbish power supply board for the replacement.


Hope this help out in solving the problem, take care

thought I would post this here for everyone.

1 blink STV 5v sense DG Board

2 blinks 15v SOS D Board

3 blinks 3.3v SOS D Board

4 blinks Power SOS P Board

5 blinks 5v SOS D Board

6 blinks Driver SOS 1 SU / SD / SC Boards
(SC energy recovery circuit)

7 blinks Driver SOS 2 SU / SD / SS Boards
(SC floating voltage area)

8 blinks Driver SOS 3 SS Board
(SS energy recovery circuit)

9 blinks Panel Config. SOS

10 blinks Sub 5v SOS / Main 3v SOS DG Board
DTV 9v SOS / Tuner Power SOS

11 blinks Fan SOS PB Board

12 blinks Sound SOS H Board

13 blinks Communication error DG Board
with IC8001 (Pesks Lite 2)

the blinking power light is actually a diagnostic of a faulty part inside the set.

Here is the diagnostic info and which part you need to replace.

1 blink STV 5v sense DG Board

2 blinks 15v SOS D Board

3 blinks 3.3v SOS D Board

4 blinks Power SOS P Board

5 blinks 5v SOS D Board

6 blinks Driver SOS 1 SU / SD / SC Boards
(SC energy recovery circuit)

7 blinks Driver SOS 2 SU / SD / SS Boards
(SC floating voltage area)

8 blinks Driver SOS 3 SS Board
(SS energy recovery circuit)

9 blinks Panel Config. SOS

10 blinks Sub 5v SOS / Main 3v SOS DG Board
DTV 9v SOS / Tuner Power SOS

11 blinks Fan SOS PB Board

12 blinks Sound SOS H Board

13 blinks Communication error DG Board
with IC8001 (Pesks Lite 2)

if this set is still unedr warranty, please use the warranty to replace the part. Else, have a professional install the new part for your safety.

hope this helps.

regards,

voodoo

Push the "R" button (last button on the left side) two times.
The the "sos" should be deleted.

I also uploaded the manual (only in french). The solution ist on page 10.