Question about Whirlpool Ultimate Care II LSQ9564J Top Load Washer

Open Question

Washer won't spin an it makes noise - Whirlpool Ultimate Care II LSQ9564J Top Load Washer

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Anonymous

  • 100 Answers

SOURCE: Washer won't spin, but making funny noise and water drains

You have a broke motor coupling broken between the motor and transmission the part is not expencive but a little hard to explain how to put it in.

Posted on Mar 29, 2009

Ad
Joe Onley

Joe Onley Sr.

  • 363 Answers

SOURCE: washer won't agitate after filling, grinding noise

this could be the coupling for the motor/transmission.

follows are instructions for removing the cabinet:

  • Using a Phillips screwdriver, remove the screw from each side of the console.
  • Pull the console forward and up to remove the tabs on the bottom of the end caps, out of the holes in the top.
  • Lift the console up and lay it on its back.
  • Unplug the harness connectorfor the lid switch.
  • Insert a flat screwdriver into the front edge of the clip (located on both sides), and pry back. Remove both clips from the holes in the cabinet and slide down the other end of the clips and out the slot in the rear panel.
  • Open and hold the lid while grabbing the cabinet front opening. Be sure when tilting the cabinet that the back edge clears the vacuum break.
  • Tilt the top of the cabinet toward you by pulling on the lid and opening of the cabinet. This releases the back slots of the cabinet from the tabs in the back of the base.
  • Carefully pull the cabinet away from the base of the washer and set it aside.
    Now you have access to most of the parts.
Now on the front of the base, you will see the pump. This is held on with two clips, Pop these off and pull the pump straight off the motor. The motor has two clips on it as well, (remove any screws if they are there, some have them, some don't) and pull the clips away. The motor will want to fall. Keep a firm steady hand under it to prevent damage to floor or motor.

Look on the back of the motor and see if you see a little rubber disk with 6 holes. There is a three pronged connection on the motor as well as the transmission. If this coupler is not broken, you may have a bad transmission. To check for a bad transmission, take something that you can place over one of the prongs on the connection, and spin that first clockwise and note what the agitator does. Now spin it counterclockwise and see if the basket inside the tub starts to spin. If nothing happens either way, you probably have a bad transmission. If you get action from the transmission, then you just need the coupler, which you can get one at a local appliance parts store. Replace the broken parts and replace motor/pump assy.

Hope this helps :)

Joe

Posted on Aug 29, 2009

TheMobilian

Dan Webster

  • 8220 Answers

SOURCE: The spinning thing won't spin

The motor has a double pole on it. The pump is driven on one side of the motor. The basket is driven on the other end of the motor. So if the water is pumped out then the lid switch is fine. What you have is a broken drive coupler. Usually breaks on a heavy load like rugs or quilts. Low water on a heavy load can break it too. Or simply old age.
themobilian_2315.jpgthemobilian_2316.jpg
Video:
Repair manual and more photos HERE

If you need further help, reach me via phone at https://www.6ya.com/expert/dan_73bbd84fe1d95b61

Posted on May 07, 2011

Jack Hunter

  • 139 Answers

SOURCE: Final spin won't go through... makes a squiky noise and no high speed spin

first how old is your machine. second is it under warranty? third have you tried to spin in all selections to see if your timer is working?

Posted on Dec 12, 2011

MNfisherman

Nate Stansfield

  • 11896 Answers

SOURCE: Whirlpool washer WTW5510VQO will fill, spin and drian but won't agitate, just makes a clicking noise.

If this is just clicking then the agitator bearings stuck or something is jamming it.

Posted on Jun 06, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

I have a Whirlpool Gold washer (MOD# GSQ9669LW0). The washer makes a grinding noise below when in operation. Spins when agitating, but not in rinse mode. Water still pumps out in final spin.


This machine can get items stuck in the drum, the bearings can go bad etc. https://www.repairclinic.com/RepairHelp/How-To-Fix-A-Washing-Machine/38-5-620929-/Whirlpool-Washer-won-t-spin-GSQ9669LW0.

Oct 16, 2017 | Whirlpool Washing Machines

1 Answer

Washer won't spin and makes noise on spin cycle


Sounds as if it just a broken belt. Take the back off and find where the belt is located to see if broken. Depending on the washer they can be easy to fix

Jan 05, 2013 | Washing Machines

1 Answer

Won't drain and won't spin ,makes a clicking sound


sound as though the drain pump has something hitting the impeller making the clicking noise,and the filter basket next to the pump is blocked by debris and not letting it drain

Sep 01, 2012 | Maytag MAH6700AWW Neptune Front-Load...

1 Answer

Whirlpool washer WTW5510VQO will fill, spin and drian but won't agitate, just makes a clicking noise.


If this is just clicking then the agitator bearings stuck or something is jamming it.

Jun 05, 2012 | Whirlpool Washing Machines

1 Answer

Final spin won't go through... makes a squiky noise and no high speed spin


first how old is your machine. second is it under warranty? third have you tried to spin in all selections to see if your timer is working?

Dec 12, 2011 | Whirlpool Cabrio WTW6600SBT Top Load...

1 Answer

Won't spin out and makes a humming noise


Wait for your handsome husband to come home and have him fix it. jk

Nov 09, 2011 | Maytag MAH6700AWW Neptune Front-Load...

1 Answer

My washer was making a noise when spinning, it now won't spin


sounds like the bearings could you tell me the model no and i will tell you how much it will cost can be very expensive unless you can do it yourself i cant guide you through somtimes its not cost effective to repair

Nov 09, 2011 | Hotpoint Washing Machines

1 Answer

The washer filled up with water but not won't drain spin and is making a funny noise . It's an older magic chef.


The most common issue would be the coupler for the motor transmission. It is a rubber coupling and when it goes bad it makes a grinding, or whirring noise and the machine won't spin or wash. You need to remove the cabinet and look directly under the tub where the motor and tranny connect. This is a reletivly easy and cheap fix. Just google how to replace motor coupling on a top load washer and you may also include your make and model for more direct instructions.

Jun 23, 2011 | Washing Machines

Not finding what you are looking for?
Whirlpool Ultimate Care II LSQ9564J Top Load Washer Logo

Related Topics:

135 people viewed this question

Ask a Question

Usually answered in minutes!

Top Whirlpool Washing Machines Experts

Marvin
Marvin

Level 3 Expert

85216 Answers

Gerry Harvey
Gerry Harvey

Level 3 Expert

1481 Answers

jimorris77

Level 3 Expert

411 Answers

Are you a Whirlpool Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...