Why is the front of frig.around door seal get extremely hot

You mean unplug and replug, yes?

It sounds like something is being reset. This should reset on its own if the door is left closed for a while.
Some frigs have a timer on the light so that if the door is left slightly open the light which gives off enough heat to defrost the frig or freezer will shut off after a time. Make sure the door is closing and that the seal is holding. A large door can sometimes shift on the hinge and go out of alignment. Measure the projection of the edge of the door from the face of the frig box. It will be a few inches (thickness of the door plus rubber seal to the frig box). This measurement should be the same all around the door. If it is not close to the same the door has shifted. If you are handy figure out which hinge has moved, loosen the screws, adjust and retighten. If you are not so handy, this could make things worse real fast. It is like adjusting cupboard doors in that you make the top right corner go in by pulling the bottom left corner out, for example.

The switch can easily be tested by pushing on the switch when the door is open. If you have one switch per door, it turns the light on and the fan off when the door opens. If you have two switches per door, one turns the light on and the other turns the fan off.

While the frig has your attention, pull the grill off and very carefully vacuum the dust off the radiator looking thing and all around. Wait for the evaporaror fan to stop running! This will greatly improve the efficience and lengthen the life of your frig. Your instruction manual will actually tell you to do this... If you have a dusty house do this every couple of months. I've got a pair of subzeros that are now 27 years old. I just had one of the doors shift and ice was forming on the back wall inside.

One some newer refrigerators, the manufacturer runs a loop of refrigerant tubing up and around the corners of the door seal area. While the refrigerator is running, this tubing will get somewhat warm--even hot if the room temp is hot like in summer. What this tubing and heat does is keep the door seal areas from sweating like a glass of water with ice cubes in it. If it is extremely hot, too hot to touch I would call for service and have it checked out. Some heat is normal.

Most modern refrigerators have heaters around the gasket to keep frost and condensation from forming. What you're seeing may be normal.

My older frost free GE Profile gets VERY hot on the sides and on the top during part of the cycle.
Is your temp indicator picking up the heat from the cycle? Check actual temp using a thermometer...hardware store should have one.
Are doors competely closed on the unit? No Food or plastic wraps/bags in the way?
Is the fan working properly, not squeaking or squealing?

on front panel around the door where the door seal goes up against is this what is hot check the compressor fan in the back of the machine when it doesnt run or is unoperational then the sides around the door get hot you might have to replace the compressor fan

When you say that it will not stay closed, what exactly do you mean? That the door seal does not meet the cabinet, that there is a gap? Is the door warped? Does it appear to be out of line with the hinges on the top and bottom? Is the space around the door when shut and looking at the front pretty much equal all the way around? I mean, when shut, does it appear that there is about 1/4 to 1/2 inch of the cabinet showing all around the door when shut? Has someone swung or leaned or tugged on the door, or closed the door or tried to close the door and something was keeping either the top or the bottom pushed out? There are adjustments on the hinges, at the attachment points to the cabinet and to the door itself. You may be able to adjust the hinge plates in or out and up and down to make the door seal better. And the box should be about half a bubble out of level, front to back, or with a slight angle front to back, in order to help the weight of the door seal to the cabinet of the refrigerator. If the door is warped, you may be able to determine which way it is bent, out at top, out a bottom, side to side, ect. and take it off the hinges and gently attempt to straighten this bend. If you are careful, and can determine there is warping at the top or bottom, you may be able to "straighten" the door while attached to the hinges. Gentle pressure is the procedure, GENTLE, GENTLE. Don't get the BIG HAMMER out and go to banging away. Just a push up here, and a tug down there, and you may be able to cure this fairly easy. You must first determine which way the door is warped, and then move it back the other way. It should seal the gasket to the cabinet, not so much attach the door to the cabinet edges, but a firm seal that takes a tug to open. And no air gaps. Are the products inside the refrigerator "sweating". This is the drawing of warmer room air into the cabinet and condensation forming. The door needs to seal in order to keep the cold air in, and the outside air OUT. I an extreme warping, you may have to replace the door, or use bungee straps to keep it shut. which will be a pain, removing those every time you need in it. I would try and determine where it may be bent or warped, and gently bend it back the other way a little at a time till I have the seal connecting all the way around. Once there, QUIT. No more bending. When the seal connects all the way around, you are finished. Problem solved. I wish you luck and hope that you can solve this fairly easy. Remember, be Gentle. It will warp easily. And no hanging on the door!

as with alot of refrig units the rubger strip has a warming coil that keeps the door from sticking they keep an even warm temp so as opening and closing the door easy there could be a burn spot in the strip and causing the strip tp be warmewr than it should be almost hot should call a fridge expert after you convince your other half there is a prob normally most fridges have a plan magnetic strip to seal the door

Either your coils are dirty ( clean from the front after removing the kickplate , only what you can get to ) or , the condensor fan motor is bad ( motor which cools the compressor ) .

First take the grill off at the bottom under the doors look at the grate under the frig That is your condenser it will probably be covered in dust clean it off the see if you can fill air blowing under the frig there is a fan under there that keeps that coil cool and it runs around the door to keep condensation from build around the doors if no air is blowing take the back panel behind the Frig and there should be a fan running if the compressor is running this will also cause the compressor to over heat and will not cool as well but it might just need to be cleaned Good luck

sounds like you have a gap in the door seal, which results in condensation forming inside unit. Use a blow dryer to heat the seal around the door and ensure that the fit is tight.