What does it mean when its says enter station

out of range means it can't receive a signal from the base station. The most likely problem lies with the base station. Special when 2 or even more handsets are giving this message.
Try to reset (unplug the power cord and reinsert it) the base station. When it does not come back after half a minute, the station must have a major problem.

This would normally indicate "Service station error". I found the following solution elsewhere on Fixya for the HP Plotter T1100, but looks like it is for the technically minded.

"Remove right cover, remove & take out service station, check any objects in service station movement, remove motor clean entire unit with water you can find out lot of ink inside & too dirty clean it allow to dry apply grease for smooth movement( pl take care of pumping unit & tubes), fix it back, perform service station test ( to enter in service mode switch of the machine with power off button from front panel hold UP arrow button & OK key button then which on the from front panel button, wait till enter in service mode scroll to service station enter, three options service station,primary motor and aerosol motor select service station, enter wait till result papers on panel)."

Hope this helps.

Tech guys only:
Service station error..Remove right cover, remove & take out service station, check any objects in service station movement, remove motor clean entire unit with water you can find out lot of ink inside & too dirty clean it allow to dry apply grease for smooth movement( pl take care of pumping unit & tubes), fix it back, perform service station test ( to enter in service mode switch of the machine with power off button from front panel hold UP arrow button & OK key button then which on the from front panel button, wait till enter in service mode scroll to service station enter, three options service station,primary motor and aerosol motor select service station, enter wait till result papers on panel) best of luck...

Tech guys only:
Service station error..Remove right cover, remove & take out service station, check any objects in service station movement, remove motor clean entire unit with water you can find out lot of ink inside & too dirty clean it allow to dry apply grease for smooth movement( pl take care of pumping unit & tubes), fix it back, perform service station test ( to enter in service mode switch of the machine with power off button from front panel hold UP arrow button & OK key button then which on the from front panel button, wait till enter in service mode scroll to service station enter, three options service station,primary motor and aerosol motor select service station, enter wait till result papers on panel) best of luck...

Tech guys only:
Service station error..Remove right cover, remove & take out service station, check any objects in service station movement, remove motor clean entire unit with water you can find out lot of ink inside & too dirty clean it allow to dry apply grease for smooth movement( pl take care of pumping unit & tubes), fix it back, perform service station test ( to enter in service mode switch of the machine with power off button from front panel hold UP arrow button & OK key button then which on the from front panel button, wait till enter in service mode scroll to service station enter, three options service station,primary motor and aerosol motor select service station, enter wait till result papers on panel) best of luck...

Changing ringing on a Partner system is done on either ext 10 or 11.
At one of those ext's press the feature key and "00"
Next press the left hand intercom twice
The display should say system programming

Press the right hand intercom once. The display should say Central telephone Programming.

Enter in the extension number that you want to program.

Press the line that you want to ring.
A solid light on the line means immediate ringing
A slow flashing light means delayed ringing (meaning the phone will wait 3 rings before starting to ring.)
A fast flashing light means no ringing.

When finished with that station press the right hand intercom and enter in the next extension to program and set ringing accordingly.

Press feature "00" to logout

Use this steps to unlock your mobile

1 - Switch ON your Motorola Droid with a NOT ACCEPTED SIM Card,
2 - Phone will display "Enter Special Code",
3 - You can now enter the Unlock Code.

If you need unlock code means you can get the unlock code here theunlockarena.com

Changing ringing on a Partner system is done on either ext 10 or 11.
At one of those ext's press the feature key and "00"
Next press the left hand intercom twice
The display should say system programming

Press the right hand intercom once. The display should say Centralized Programming.

Enter in the extension number that you want to program.

Press the line that you want to ring.
A solid light on the line means immediate ringing
A slow flashing light means delayed ringing (meaning the phone will wait 3 rings before starting to ring.)
A fast flashing light means no ringing.

When finished with that station press the right hand intercom and enter in the next extension to program and set ringing accordingly.

Press feature "00" to logout

Your phone (KX-TC911-B) can store up to 10 phone numbers. Numbers 0 - 10 are your memory stations.

1. Make sure the TALK indicator light is off.
2.Press Program. The TALK indicator light will start flashing.
3. Enter the phone number.
4. Press AUTO.
5. Press a memory station where you want to store a particular phone number.
6. You will hear a confirmation tone. 1 beep means the number has been successfully stored.
2 beeps mean, you entered the same number that has already been previously stored.
Click on the link if you would like to have a pdf copy of the manual/tutorials.

try pressing the memory button, it may be waiting for a direct dial out, you can download users manual from panasonic global website