Question about Brother CS-6000

Open Question

I have a Brother cs-6000. The bottom of the bobbin rewinder hits agains the the bar when it tries to rewind. It's the little part that you put the end of the tread through after you put the bobbin on. Then I move it to the right and it bumps the bar asnd wont wind.

Posted by Anonymous on

Ad

5 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

SOURCE: I need to rewind a new bobbin

My SE-270D bobbin winder is located on the top of the machine to the far right. From the picture of your machine it looks to be in the same place. The larger spindle is for the spool of thread and the shorter spindle is for the bobbin.
You need to wnd the thread around the bobbin a few times just to make sure it is started properly, and then move the bobbin either forward or backward to engage. (It's different on some machines.) You may also have to move the outer edge of the machine wheel (the large wheel on the outside right) to keep the needle from moving up and down while the bobbin is filling. When the bobbin is full the machine should shut off by itself.
Then you will have to re-tighten the machine wheel to engage the needle.
Hope this helps.

Posted on Apr 05, 2009

Ad

Anonymous

  • 8 Answers

SOURCE: brother CS 8060 bobbin wont wind...but motor runs

no idea... did you lock thread onto bobbin so it holds to wind?

Posted on Jul 18, 2009

paj42

  • 1116 Answers

SOURCE: bobbin will not rewind

SE270D. Lift the bobbin and reposition, making sure it is down against the pin.

If this is not the problem, a Sidewinder Bobbin Winder (auxiliary bobbin winder sold with most sewing notions) is a lot cheaper than taking the machine in for service.

Posted on Mar 14, 2010

ju222dy

Judy Tew

  • 8 Answers

SOURCE: Cannot wind the bobbin

Mine stopped working too. Gave up and wound bobbins by hand for a while until I broke down and took the machine apart -- an ordeal to figure out. I found that a pliable ring on the winder was completely disintegrated (gummy plastic-like stuff). An online search found this -- a bobbin "tire" which I THINK is the part I need: http://www.sewingpartsonline.com/bobbin-winder-tire-brother-x55238051.aspx. Hope this helps. --Also cleaned all the lint out when I had the machine opened up. They don't make it EASY!

Posted on Aug 09, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to trouble shoot without a manual?


you can download a free manual at //www.generalmanual.com/Home-Sewing-Embroidery-Machines/Brother-CS-6000i-Sewing-Machine.htm


F4 might mean that the bobbin on the top is in the position for rewind, slide bobbin to the right for the error code to go away. Hope this helps, Sandy

May 03, 2014 | Brother CS-6000i CS6000i 60-Stitch...

1 Answer

Brother cs-6000 will not sew, the top thread go through and tangles on back, and the bobbin thread is a straight line and can be easily pulled out, please help, trying to make kids school clothes


Hi:

Ok... so try to remember that loopy stuff on top means the bobbin tension is too loose (or the top tension is too tight...)

Loopy stuff on bottom, means the top tension is too loose. (or it's not threaded right)

Now. Get some scrap of the same material. Loosen that bobbin back to where it was. RETHREAD the top, with the foot in the UP position.

Place your scrap under the foot, and sew. still have problem? clip your threads and try again only this time hold the top and bottom threads off to the side as you begin to sew. How did that do?

Adjust the top tension to the point where you start seeing the bobbin thread come up in loops to the top... then back off until the disappear.

Now... be sure you have the correct thread and needle for your fabric. A lot of problem are caused by not having the proper needle and thread.

Jul 09, 2012 | Brother CS-6000

1 Answer

Bobbin will not rewind


SE270D. Lift the bobbin and reposition, making sure it is down against the pin.

If this is not the problem, a Sidewinder Bobbin Winder (auxiliary bobbin winder sold with most sewing notions) is a lot cheaper than taking the machine in for service.

Mar 14, 2010 | Brother Sewing Machines

1 Answer

Brother CS-80 Sewing Machine Bobbin Rewind


For $30 you can buy a standalone bobbin winder (Sidewinder) at JoAnn's Fabrics or Amazon. It's a great little accessory (battery or electrical) because it saves wear and tear on your machine but also allows you to wind multiple bobbins without having to unthread the machine.

Nov 09, 2017 | Brother CS-80

1 Answer

I took my maching apart to clean the lint out and when I put it back to together the needle is hitting the feed dogs. what could be causing this!


most likely the bobbin case is not aligned correctly .Insert the bobbin case so that the projection on the boobin case aligns with the spring.

Feb 23, 2009 | Brother CS-6000

1 Answer

My needle hits metal


You have to be putting the bobin in the wrong way or it is not all the way in. I hopr this helps.

Feb 04, 2009 | Brother CS-6000

3 Answers

Brother CS-6000 Sewing Machine - Jam


I have the same problem and found that the bobbin case is scratched. These are quite expensive so I hope yours is something more simple. Keeping the bobbin area clean is also a necessity.

Jul 28, 2008 | Brother CS-6000

1 Answer

Rewinding bobbin


many old machines have problems with worn out parts check the link attached , perhaps it is a good alterative https://www.walmart.com/search/?query=bobbin%20winder&typeahead=bobbin

Mar 30, 2017 | Sewing Machines

1 Answer

Can't get Bobbin to wind properly


Verify that your thread path is correct when winding the bobbin. It has a distinctive path including a tensioner that helps your thread wind smoothly. Do not use a bobbin that is not wound smoothly because (as you already know) it could possibly break needles and damage the machine.

Brother CS 80 Sewing Machine Bobbin Rewind

Nov 09, 2017 | Kenmore 15208 Mechanical Sewing Machine

Not finding what you are looking for?
Brother CS-6000 Logo

Related Topics:

61 people viewed this question

Ask a Question

Usually answered in minutes!

Top Brother Sewing Machines Experts

Irene Tulloch

Level 2 Expert

498 Answers

Douglas Plant
Douglas Plant

Level 2 Expert

222 Answers

PHYLLIS SMITH

Level 1 Expert

19 Answers

Are you a Brother Sewing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...