Question about Black & Decker Drills

1 Answer

Stuck chuck, got screw out of center, how do I get chuck off drill ?

Cordless drill 20v LDX120

Posted by Anonymous on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.

  • Contributor
  • 2 Answers

Close the chuck onto an Alan Key and use it to twist the drill off.

Posted on Oct 31, 2017

Ad

6 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Anonymous

  • 1 Answer

SOURCE: bad chuck on 18w cordless

How to remove the chuck

Posted on Sep 03, 2008

stug_57u

Stuart

  • 99 Answers

SOURCE: drill chuck removal

The screw should be left hand thread and the chuck is normal thread. The 'workshop' way to remove the chuck is to remove the screw (done). If the jaws are still working then clamp a sturdy allen key in it and whack it against a workbench to unscrew the chuck. If holding the drill in the normal position you would stand with the workbench to your left and whack it down on that. If the jaws aren't working then you can grip the body in a vice and use large pipe grips or stiltsons on the chuck. Also check to see if the chuck spindle will accept a thin spanner to hold it, as this is a slightly more caring way to brace the spindle. Then you can can hold the spanner in the vice and use the allen key in the chuck and unscrew it that way.

Posted on Oct 25, 2008

Anonymous

  • 1 Answer

SOURCE: Chuck on Drill not moving

Re: Ryobi P205 special from Home Depot:
Confusing at first, but easy fix:
The chuck is shipped in the UNLOCKED position (and tightly unlocked, too).
I gripped mine w/rubber gloves and turned toward LOCK direction. It freed up with some effort.
But that's the trouble, it is a bit confusing because you would think you need to unlock it, but it's already unlocked.

Posted on Nov 30, 2008

rowdy45176

David Ford

  • 2176 Answers

SOURCE: Can't get the keyless chuck off cordless Makita 6095D drill.

If this is a newer tool it is probably a Torx drive screw usually a T20. The screw is LH thread and after removing it you will need to put some screws back in tool to remove the chuck. First shift the gear selector to the low setting and the clutch to the drill only. Next get a bent handle allen wrench about the capacity of the chuck install the short end of wrench in chuck and tighten. Put the chuck on a block or wood or a workbench to support is and turn the wrench to about a 30 degree angle in the counterclockwise position. The chuck has standard threads so you want to hit the wrench with a hammer to loosen it. This might take a few tries but it will work. Good luck

Posted on Dec 31, 2008

meleemore

Anthony Smith

  • 19 Answers

SOURCE: sds drill stuck in chuck

tap it lightly with a ball pin hammer, if that dosnt shake it out try opening it and useing something to push it through

Posted on May 05, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

3/8" cordless driver can't change the


If debris enters the chuck it may no longer turn for adjustment. Spray plenty of wd40 into chuck and allow plenty of time for oil to do its magic. Hold chuck/drill pointing down and turn drill in both directions to clean out debris. If chuck is too far gone, remove the center screw (backwards thread) and remove the chuck(threaded on). Replace the chuck with new generic part from Lowes (about $25.).

Sep 20, 2011 | Dewalt Drills

1 Answer

How do I change the keyless chuck assembly on a cordless drill


It depends on what model but there held by eighter a screw or on x shaped fasiner in the center of the chuck open it up as far as you can hold the chuck in a vice and remove the screw and the chuck should come off

Nov 23, 2010 | Black & Decker Drills

1 Answer

Removel of chuke


Open your chuck as far as it will go and look inside. If you see a screw go to www.ereplacementparts.com/article/890/How_to_Remove_a_Drill_Chuck.html for a good how to on this.

If there is no screw inside the chuck you have to take the drill to a Dewalt service center and have them remove it. It takes a special jig to remove it and I don't think you want to spend over $200 to remove one chuck. Do not try to use the taper-fit tool on a cordless drill, they do not use the taper fit chucks.

Sep 09, 2010 | Dewalt DC920KA Heavy Duty Xrp 18V Cordless...

1 Answer

Hi i broke the chuck on my 1/2 makita cordless


Put the biggest hex key you have in the chuck and tighten it then hit it clockwise with the spindle lock engaged a couple of times. The screw in the chuck will then undo clockwise and the chuck can be undone after by putting the allen key back in and unscrewing it anti-clockwise maybe with a light tap from a mallet.
Hope this helps
Jon

Jul 01, 2010 | Makita 6349DWDE 18-Volt Ni-MH 1/2-Inch...

1 Answer

Cordless Drill, Keyless Chuck stuck in full open position.


if chuck is wide open ,look down inside there should be an allen screw or bolt at the bottom of the chuck it should undo anti clocwise and the chuck comes off

Aug 18, 2009 | Dewalt DW056 18 Volt Cordless Impact...

1 Answer

How to unlock the chuck


this how to get a chuck off a drill.look inside the chuck for a screw. it will be a left handed screw.once you get the screw out put the chuck in a vice . you will need to squeeze it very tight. then put the drill in reverse and pull the trigger.if i wont come off you will need to hit the chuck with a hammer while you are holding the trigger. if you have a bit stuck in the chuck and cant get it out put the chuck in the vice and hit it very hard with a hammer until the chuck falls apart.i work on drills every day ,this is the only way we have found that works

May 30, 2009 | Milwaukee 0612-20 14.4v Cordless Drill Kit...

1 Answer

Removal of chuck


this type of drill don't have any chuck screw in the center of the chuck.alos u need special jig to remove the chuck

Aug 11, 2008 | Dewalt DC920KA Heavy Duty Xrp 18V Cordless...

3 Answers

Dewalt dw997 drill clutch stuck


your drill required trans assy & clutch assy for $132.00 plus tax canadian max repair/
thanx

Apr 12, 2008 | Dewalt 18 Volt Compact Drill Kit

Not finding what you are looking for?
Drills Logo

Related Topics:

341 people viewed this question

Ask a Question

Usually answered in minutes!

Top Black & Decker Drills Experts

JOHN LAPIER

Level 3 Expert

2595 Answers

Marvin
Marvin

Level 3 Expert

85222 Answers

Thomas F. Schneider

Level 3 Expert

2715 Answers

Are you a Black & Decker Drill Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...