How can i program my tv without remote

Your TV must be set in cable mode for channels higher than 69, and your cable provider must allow those channels to be received without a cable box. Menu, Channels, switch air to cable, run auto scan. If it receiving those channels unencrypted, it will find those channels.

on B:Press the MENU button on the remote.Select Setup.Select Auto Program.Choose Air or Cable.Select Auto Program to let the TV reprogram the channels.Check that the channel is programmed into memory. There are a couple of ways to do this: Use the TV menu system. Accessing this setting varies depending on the model TV that you own. Here are two options that are common on many TV's: Option A:Press the MENU button on the remote.Use the VOL and CH buttons to move through the menu and add any missing channels try this if not r
Do a full reset if this dosnt work

Codes listed in my manual for White Westinghouse are 0169 or 0003 or 0014 or 0043. Are yousure though there isn't a flip down panel somewhere which gives you the option to access "enter"

What brand/model TV do you have? If the TV has several input options, make sure that the TV is set to the TV mode. (Use the Input or Source button on the remote, some TVs have this on the TV as well but not always)

Some can only do a channel scan with the original remote. My old Emerson CRT (~20 years old) launched a channel scan when I pressed the Add and Delete Channel buttons together on the remote. Fortunately even when most of the buttons failed on that remote, the channel scan still launched.

Other TVs from that time frame have an channel scan button in the control panel. Often these are hidden behind a panel to avoid accidental resets.

More modern TVs usually have the scan as part of the menu. Depending on the TV, press Menu on the remote (or if available on the TV (sometimes can be done by pressing Ch+/Ch- together)). Then look for a Setup option or a TV icon. If you have a Setup menu, you will then need to go to the TV submenu. Then find the option for setting the input signal (TV/cable) and then you should be able to launch a channel scan. (Usually the Ch+/Ch- (up/down) and Vol+/Vol- (left/right) buttons will navigate through the menus.)

Unfortunately, without the make and model, I can't give you any more help. Please write back with your brand of TV and I'll check if I have the manual in my stack.

Cindy Wells
(low end universal remotes do not always include the menu or source button. If your TV doesn't have them, you may need a different remote. The ones that can be programmed via a USB connection are the easiest to set up.)

Hello

In the CBL/SAT or TV mode, use the FAV key to start a 3-second scan of all

channels.Or, if programmed, use the FAV key to scan only your favorite
channels to view a desired channel

Press CBL/SAT or TV once.

Press FAV once.

• IfFavorite Channel Scan has been set up, scanning of

favorite channels will start with up to 100 channel changes
or until stopped by pressing any key.

IfFavorite Channel Scan has not been set up, scanning

will start with the current channel, and continue up to
100 channel changes or until stopped by pressing any key.

To stop scanning channels at any time, press any key
once.

Your TV is most likely locked to that station because it doesn't have any other channels programmed in.

In the menu for the TV, run a channel scan. This will take probably 30-45 minutes for most TVs and will program the available channels into the TV so that they become available.

Get a zenith universal remote with enter button, go to channel setup and it will apear cable- air, choose cable but press enter on the remote and it will start to program itself and let it finish, it will take like 10-15 min to scan

Local digital channels should be available from the cable TV line from the wall. Your TV has to have a digital tuner. You can do a channel set-up scan with the TV. Then do channel up and down or channel # access to get to desired channel.

Try website 1-800-Remotes Factory orginal.To buy an exact orginal remote.Have all the funsctions,usally the universal remote don't.

Try unplugging it for 2 minutes then se what happens. Make sure that none of the buttons on the TV or remote contol are stuck (especialy if remote is near TV).